manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 73 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 73

3.12  Connecting Sensors to the Frequency Module

Sensors and Signal Output Sources That Can Be Connected

The table below shows the sensor and signal output source that can be connected. Appropriate input 
presets are provided for each sensor and signal output source. For information about presets, see 
Input Setup in section 1.7, 

“

Configuring Frequency, Revolution, Period, Duty Cycle, Power Supply 

Frequency, Pulse Width, Pulse Integration, and Velocity Measurements,” in the user’s manual.

Sensor and Signal Output Source

Preset Name

5-V logic signal, 5-V output sensor, and sensor with TTL output

Logic 5V

3-V logic signal and 3-V output sensor

Logic 3V

12-V driven relay/sequence circuit and 12-V driven sensor

Logic 12V

24-V driven relay/sequence circuit and 24-V driven sensor

Logic 24V

Sensor/Encoder that outputs positive and negative voltages and sensor that outputs sine waves ZeroCross
100-VAC power supply (connected via the isolated probe (700929))

AC100V

200-VAC power supply (connected via the isolated probe (700929))

AC200V

Power-generating electromagnetic pickup

EM Pickup

Open collector (0 to 5 V) output sensor, contact output

Pull-up 5V

*

*  For the internal equivalent circuit when the preset setting is Pull-up 5V, see the “Frequency Measurement” 

section in chapter 2, “Vertical Axis” in the feature’s guide (IM DL850-01EN).

Precautions to Be Taken When Connecting to Sensors or Signal 

Output Sources

 

WARNING

Over-Range Indication

If over-range is indicated, the DL850/DL850V may be receiving a voltage higher than the 
observed waveform or measured waveform values. To prevent electric shock, change the 
vertical scale with the SCALE knob so that the entire amplitude of the waveform is displayed 
within the waveform display area, and check the input voltage level.

 

     

Over-range indication

Indicates the number of the channel that over-range is occurring on.

Channel indication when over-range is occurring on multiple channels

Indicates the smallest number among the channels that over-range is 

occurring on.

 

CAUTION

•  The maximum input voltage for direct input is indicated below. Applying a voltage exceeding 

this value can damage the input section. When applying a high voltage of 42 V or more, be 
sure to use an isolated probe (the 700929 or 701947).

  Maximum input voltage: 

42 V (DC + ACpeak) (CAT II)

•  The minimum input voltage is 0.2 Vpp. At voltage amplitude less than 0.2 Vpp, the 

measured values may be unstable.

•  Attach/Remove the sensors after confirming that the rotating object to be measured is 

stopped.

•  Set the preset to electromagnetic pickup (EM Pickup) only when using the electromagnetic 

pickup.

3-32

IM DL850-03EN

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов