manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 63 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 63

3.7  Connecting Measurement Leads

Connecting Measurement Leads

When you measure voltage using the 701261 (UNIVERSAL), 701262 (UNIVERSAL (AAF)), 
701267 (HV (with RMS)), and 701265 (TEMP/HPV), connect the measurement leads of a plug-in type 
terminal to the input terminal.

 

H (red)

L (black)

For the 701267

For the 701261, 701262, and 701265

 

WARNING

•  When connecting a device under measurement to the instrument, be sure to turn off the 

device. It is extremely dangerous to connect or remove measurement leads while the 
device under measurement is on.

•  When measuring high voltages, do not connect a plug-in type terminal with exposed 

conducting parts to the input terminal to be used as a measurement lead. It is very 
dangerous, if the connector comes loose.

Precautions to Be Taken When Using the Modules

•  To prevent the possibility of electric shock, always connect measurement leads that 

match the voltage range that you are measuring to the signal input terminals of the 
701261 (UNIVERSAL), 701262 (UNIVERSAL (AAF)), 701267 (HV (with RMS)), and 
701265 (TEMP/HPV).

•  When measuring high voltages using the 701267 (HV (with RMS)), use a measurement 

lead 758933 and alligator clip 701954.

Maximum Input Voltages and Maximum Allowable Common Mode Voltages for the Modules

Applying a voltage exceeding the value indicated below may damage the input section. If the 
frequency is above 1 kHz, damage may occur even when the voltage is below this value.

•  For the 701261, 701262, and 701265

  •   Maximum input voltage (across the input terminals, H and L,

1

 at a frequency of 1 kHz or less)

    42 V (DC+ACpeak)
  •   Maximum allowable common

 

mode voltage (across the input terminals, H or L, and 

earth,

2

 at a frequency of 1 kHz or less)

    42 V (DC + ACpeak) (CAT II, 30 Vrms)

3-22

IM DL850-03EN

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов