manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 189 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 189

App-28

IM DL850-03EN

Appendix 6  High-Voltage 100 kS/s, 16-Bit 

Isolation Module (with RMS) (701260) 

Specifications

The specifications for the High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS) (701260) are 
provided below. This input module (701260) will not comply with safety standard EN61010-1 or 
EN61010-2-030 after September 30, 2013.

Item

Specifications

Standard operating 

conditions

Temperature:

Humidity:

23 ±5°C

20 to 80% RH

After a 30-minute warm-up and after calibration

Effective measurement 

range

20 div (±10 div around 0 V, display range: 10 div, when Variable is OFF)

Number of input channels 2

Input coupling

AC, DC, GND, AC-RMS, and DC-RMS

Maximum sample rate

100 kS/s

Input format

Isolated unbalanced

Frequency characteristics

1

(−3 dB point when a sine 

wave of amplitude ±3 div 

is applied)

Waveform observation mode:

RMS observation mode:

DC to 40 kHz

DC, 40 Hz to 10 kHz

Voltage-axis sensitivity 

setting 

20 mV/div to 200 V/div (1-2-5 steps) (when using 1:1 probe attenuation)

Maximum input voltage 

(at a frequency of 1 kHz or 

less)

Combined with the 700929(10:1) or 701947 (100:1):

2

Combined with the 701954 (1:1):

5

Direct input or cable not complying with the safety standard:

8

1000 V (DC+ACpeak)

850 V (DC+ACpeak)

850 V (DC+ACpeak)

Maximum allowable 

common mode voltage 

(at a frequency of 1 kHz or 

less)

Working voltage of safety standard

Combined with the 700929 or 701947 (across probe tip H and earth

3

):

(across probe tip L and earth

4

): 

Combined with the 701954 (1:1)

 

(across tip H and earth

6

):

(across tip L and earth

7

):

1000 Vrms (CAT II)

400 Vrms (CAT II)

700 Vrms (CAT II)

400 Vrms (CAT II)

Direct input or cable not complying with the safety standard:

9

(across the input terminal, H or L, and earth)

30 Vrms (42 VDC+ACpeak)

Vertical (voltage) axis 

accuracy DC accuracy

1 

Waveform observation mode

DC accuracy

RMS observation mode

DC accuracy

AC accuracy (when a sine wave is input)

AC accuracy (when the crest factor is 2 or less)

AC accuracy (when the crest factor is 3 or less)

±(0.25% of 10 div)

±(1.0% of 10 div)

±(1.5% of 10 div)

±(2.0% of 10 div)

±(3.0% of 10 div)

At frequency of 40 Hz to 1 kH

At frequency of 40 Hz to 1 kH

At frequency of 40 Hz to 1 kH

Input connector 

BNC connector (isolated type)

Input impedance 

1 MΩ ± 1%, approx. 35 pF

−3 dB point when AC 

coupled low frequency 

attenuation point

1 Hz or less (0.1 Hz or less when using the 700929, 0.01 Hz or less when using the 701947)

Common mode rejection 

ratio

80 dB (50/60 Hz) or more (Typical

10

)

Residual noise level 

(Input section shorted)

±1 mV or ±0.02 div whichever is greater (Typical

10

)

Withstand voltage 

3700 Vrms for 1 minute (across each terminal and earth) (60 Hz)

Allowable transient surge 

voltage (instantaneous)

±5200 Vpeak (across each input terminal and earth)

 

Insulation resistance 

500 VDC, 10 MΩ or more (across each input terminal and earth)

A/D conversion resolution  16 bit (2400 LSB/div)

Temperature coefficient 

Zero point: 

Gain: 

±(0.02% of 10 div)/°C(Typical

10

)

±(0.02% of 10 div)/°C(Typical

10

)

Response time (only when 

observing RMS) 

Rising (0 to 90% of 10 div):

Falling (100 to 10% of 10 div):

100 ms (Typical

10

)

250 ms (Typical

10

)

Bandwidth limit

Select from OFF, 10 kHz,1 kHz, and 100 Hz

Cut-off characteristics: −12 dB/OCT (Typical

10

)

Probe attenuation setting  Voltage probe:

Current probe:

1:1, 10:1, 100:1, 1000:1

10 A:1 V (for the 700937/701933), 100 A: 1 V (for the 701930/701931)

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов