manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 159 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 159

6-51

IM DL850-03EN

Specifications

1

2

3

4

5

6

App

Index

6.14  Logic Probe Specifications

High-Speed Logic Probe (700986) Specifications

Item

Specifications

Number of inputs

8

Input format

Non-isolated (all the bits share the same ground with the DL850/DL850V and each other)

Maximum input voltage

42V (DC + ACpeak) (CAT II, 30 Vrms), between the probe tip and ground
(at a frequency of 1 kHz or less)

Response time

Within 1 μs

Input impedance

100 kΩ or more

Threshold level

Approx. 1.4 V

Isolated Logic Probe (700987) Specifications

Item

Specifications

Number of inputs

8

Input format

Isolated (all bits are isolated)

Input connector

Safety terminal type (for banana plug) × 8

Input switching

Each bit can be switched to AC or DC input.

Input signal display

The H/L state of each bit is indicated with LEDs (the LEDs illuminate to indicate H).

Applicable input range

During DC input: H/L detection of 10 VDC to 250 VDC
During AC input: H/L detection of 80 VAC to 250 VAC at 50/60 Hz

Threshold level

During DC input:

6 V ± 50% (High level: 10 to 250 VDC, Low level: 0 to 3 VDC)

During AC input:

50 VAC ± 50% (High level: 80 to 250 VAC, Low level: 0 to 20 VAC)

Response time

During DC input: 1 ms or less
During AC input: 20 ms or less

Input impedance

Approx. 100 kΩ

Maximum input voltage

250 Vrms

1

 (CAT II)

(between the H and L terminals of each bit)
Maximum allowable common 

mode voltage

250 Vrms

1

 (CAT II)

(between input terminal H or L and the ground)
Maximum allowable voltage 

between bits

250 Vrms

1

 (CAT II)

Withstand voltage

2000 VAC for 1 minute

(between the input terminals and the ground)
Insulation resistance

500 VDC, 10 MΩ or greater

(between the input terminals and the ground)
Fuse

2

Location

Max. rated voltage

Max. rated current

Type

Standard

H side of input 

terminal

250 V

50 mA

Time lag

VDE/SEMKO 

approved

1   Make  sure  that  the  peak AC  voltage  does  not  exceed  350  V  and  that  the  DC  voltage  does  not  exceed  250  V  when  the 

frequency is 1 kHz or less.

2   Because the fuses used by this instrument are all inside the case, you cannot replace them yourself. If you believe that the 

fuse inside the case has blown, please contact your nearest YOKOGAWA dealer.

Logic Probe (702911 and 702912) Specifications

Item

Specifications

Number of inputs

8

Input format

Non-isolated (all the bits share the same ground with the DL850/DL850V and each other)

Maximum input voltage

±35 V

Response time

Within 3 μs

Input impedance

10 kΩ or more

Threshold level

Approx. 1.4 V

Input methods

TTL level or contact input (switchable). During contact input: Pulled up to 5 V

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов