manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 105 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 105

5-5

IM DL850-03EN

External Signal I/O

1

2

3

4

5

6

App

Index

5.5  GO/NO-GO Determination I/O and External 

Start/Stop Input (EXT I/O)

Connecting to Other Instruments

 

CAUTION

•  Do not apply external voltage to the NO-GO OUT and GO OUT output pins. Doing so may 

damage the instrument.

•  When connecting the GO/NO-GO determination signal output to another device, do not 

connect the wrong signal pin. Doing so may damage the DL850/DL850V or the connected 
instrument.

•  Do not connect a USB cable to the GO/NO-GO output terminal. Doing so may damage the 

instrument.

About the External I/O Cable (720911; sold separately)

•  Do not use the cable for anything other than the DL850/DL850V external I/O.
•  Refer to the following figure to connect the cable to an external device.

 

1

6

Approx. 1.5 m

RJ-11 connector

To the DL850/DL850V

Process the wires at the 

end of the stripped cable 

as necessary.

Pin no.

Signal

Logic

1

EXT  EVENT  IN Negative logic

Wire color

Red

2

3

4

5

START  IN

GO  OUT

NOGO  OUT

Negative logic

Negative logic

Negative logic

GND

Yellow

White

Green

Blue

GO/NO-GO Determination I/O

You can apply an external signal to the DL850/DL850V’s GO/NO-GO I/O terminal and perform GO/
NO-GO determination, and you can output the results of GO/NO-GO determination from the GO/NO-
GO I/O terminal.

GO/NO-GO I/O Connector

Type

  The connector uses an RJ-11 modular jack. Use the external I/O cable accessory (720911; sold 

separately). If you are using a commercially sold cable (four-conductor modular telephone cable), 
wire the pins according to the above figure.

I/O Level

  Within 0 to 5 V, threshold level: TTL

Pinout

6

1

1

Pin no.

Signal

2

3

4

5

6

EXT  EVENT  IN

START  IN

GO  OUT

NOGO  OUT

IN

Connector on 

the DL850

OUT

OUT

Starts on low edge

Active low (GO)

Active low (NO-GO)

GND

NC (no connection)

EXT I/O

Manual event. Event input occurs on low edge.

IN

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов