YOKOGAWA CM6G Скачать руководство пользователя страница 62

Страница: 62 / 65

<8. Troubleshooting>

8-5

IM 11R02A01-02E

5th Edition : Dec. 28, 2016-00

8.5 Computing Station

If the value is all normal, each input of the computing station shows the following normal values in

the table.

Mark of input data

Normal indication

NON-CORR.

WI %

A-PRESS

500 ± 50

G-PRESS

500 ± 50

SQT. DENSITY

Same as density meter

When pre-heating circuit does not exist, 0 to 100% is almost in proportion to 0 to “the highest level WI value in the measurement

range.”

When preheating exists, about 20 to 100% is almost in proportion to 0 to “the highest level WI value of the measurement range.”.

The lamps of both alarm and fail of the computing station are lighted in the following case.
1) Lighting of the alarm lamp. (Yellow color)

It lights when the input or output signal is cut off. But in this case, the computing inside the

station keeps working. Change to Alarm display and examine the cause of the alarm.

2) Lighting of the fail lamp (Red color)

The lighting of the fail lamp means an occurrence of an abnormal trouble produced inside

the instrument. When a fail occurs, the analog output and status output reserve the value

just before the occurrence of the failure. Such hold output has a tendency of decreasing

gradually as time proceeds. When the fail lamp is on, the display of fail will be shown.

The alarm lamp lights for the abnormal operation of the pressure adjustment for the gas or

air line. The lighting when other than under the time of measurement is not abnormal.

8.6

Other Troubleshooting

Check and deal with measures mentioned in paragraph 8.1 to 8.5. As to the trouble not

mentioned in this manual, contact our service personnel and describe how the inspection goes,

and if you have any record..

Содержание CM6G


































































Результаты поиска

Содержание CM6G

Отзывы:

Похожие инструкции для CM6G

Бренды по названию

Популярные бренды

YOKOGAWA CM6G, Руководство пользователя

Результаты поиска

Содержание CM6G

Отзывы:

Похожие инструкции для CM6G

Бренды по названию

Популярные бренды