YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 98

Страница: 98 / 195

4-5

IM AQ7280-01EN

Optical

Pulse Analysis

Index

Marker Menu (Marker Mode: Line)

From the top menu, select

OTDR

Press the

Marker

soft key to display the marker menu.

Switches to the screen that is used to measure 2 Point markers.

For the measurement principle, see section 1.4.

Switches to the screen that is used to measure 5 Point markers.

For the measurement principle, see section 1.4.

Sets or clears the distance

reference.

Sets the distance reference

(marker R) at the cursor position

See page 4-3.

Clears the markers and cursors.

Preset markers.

and apply them on waveforms during

measurement when necessary.

2 Point Markers

Press the

2 Point Markers

soft key to display the following screen.

Set marker n.

Marker n is set at the cursor

position.

Set marker E.

Marker E is set at the cursor

position.

Turns the cursor link on or off

Marker n

Marker E

Marker information

Move the cursor.

Moves the cursor to set

markers.

Set the approximation method.

See page 2-3.

Note

• When you set the marker positions, set them so that the n marker is the measurement start point (the

distance reference).

• The measured loss value differs depending on the specified approximation method.

4.1 Analyzing Waveforms

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды