YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 35

Страница: 35 / 195

2-10

IM AQ7280-01EN

Setting Analysis Conditions in Detail Mode

Press the

Analysis Setup

soft key to display the following screen.

When the screen is scrolled

Set the index of refraction

(1.30000 to 1.7999).

Set the splice loss (0.01dB to 9.99dB).

Executes initialization

Press to reset the analysis settings to

their factory defaults.

Set the splitter search (OFF, ON).
Set the splitter loss (1dB to 20dB).

Set the approximation method (marker).

See page 2-3.

Set the backscatter level

For a pulse width of 1 μs:

–10.00 dB to –64.99 dB

For a pulse width of 1 ns:

–40.00 dB to –94.99 dB

Set the return loss (20dB to 70dB).
Set the end of fiber (3dB to 65dB).

Set the launch fiber cable

(Setup[OFF], Setup[ON]).

Set the pass/fail judgment

(Setup[OFF], Setup[ON]).

Set macro bending

(Setup[OFF], Setup[ON]).

Set the approximation method (event).

See page 2-3.

Index of Refraction (IOR)

The AQ7280 uses the index of refraction to calculate the distance. If you do not set the index of

refraction correctly, the distance measurement will be incorrect. The index of refraction varies

depending on the connected optical fiber cable. Enter the value recommended by the manufacture

of the cable.

The AQ7280 has the following preset indices of refraction that correspond to each wavelength.

Wavelength

Index of Refraction

Wavelength

Index of Refraction

850 nm

1.46000

1490 nm

1.46000

1300 nm

1.46000

1550 nm

1.46000

1383 nm

1.46000

1625 nm

1.46000

1310 nm

1.46000

1650 nm

1.46000

You can specify a value from 1.30000 to 1.79999.

Backscatter Level

Light that travels through an optical fiber cable displays a phenomenon known as Rayleigh

scattering. Due to this phenomenon, light is sent backwards, in the direction opposite to the

direction of propagation. This phenomenon is known as backscattering. The backscatter level

setting is used when the AQ7280 calculates the return loss and total return loss.

2.1 Setting the Measurement and Analysis Conditions

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды