YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 195

background image

6-2

IM AQ7280-01EN

6.2 Connecting an SD Card

CAUTION

• Before connecting an SD card, turn off the power.
• Do not insert the SD card in the wrong direction. Doing so may damage the SD card or the

AQ7280 or both.

French

ATTENTION

• Coupez l’alimentation électrique avant de connecter une carte SD.
• N’introduisez pas la carte SD dans le mauvais sens. Cela pourrait endommager la carte

SD ou l’AQ7280, voire les deux.

Compatible SD Cards

You can use SDHC compliant memory cards with the AQ7280. For details, contact your nearest
YOKOGAWA dealer.

Note

• When using an SD card with a PC, make sure that the PC is compatible with it. Also,

depending on the type of PC, some of the SD cards listed above may not function properly.
Check it in advance.

• SDXC is not supported.

SD memory card with a wireless LAN function (FlashAir)

The AQ7280 supports SD memory cards with a wireless LAN function (FlashAir). By using an SD

memory card with a wireless LAN function, you can access files in FlashAir and transfer data from a
PC, smartphone, or tablet.

*

From the PC, smartphone, or tablet, search for the wireless LAN access

point and connect to it. For details on searching, see the relevant manual.
* OTDR Data Transporter for Android can be downloaded from the Yokogawa Website, and OTDR

Data Transporter for iOS can be downloaded from the App Store (free software).

• Setting the auto timeout value

You can set the FlashAir auto timeout value. For the setup procedure, see section 7.6.

How to Insert an SD Card

See the Getting Started Guide, IM AQ7280-02EN.

«
...
131
132
133
134
135
...
»

Содержание AQ7280 OTDR




































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQ7280 OTDR

Бренд: Keithley Страницы: 48

Бренд: dbx Страницы: 2

Power Xpert PXM 4000

Бренд: Eaton Страницы: 28

Бренд: ICP DAS USA Страницы: 71

HYDROTECHNIK MultiHandy 2025

Бренд: ICS Страницы: 8

Бренд: ICT International Страницы: 24

Бренд: Rabid Elephant Страницы: 18

Бренд: Sensitech Страницы: 2

Бренд: Cable Ferret Страницы: 16

Бренд: R&S Страницы: 60

PowerGuide 4400

Бренд: Dranetz Страницы: 277

Бренд: Oakton Страницы: 26

Rainbow RTI-Nano Series

Бренд: Laserworld Страницы: 25

Бренд: X-Rite Страницы: 21

Бренд: DeNovix Страницы: 93

Бренд: R&S Страницы: 35

WattNode Plus WNC-3D-240-FT10

Бренд: CCS Страницы: 43

BIP LD2-T017-01-EP-S4 Series

Бренд: Balluff Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды