YOKOGAWA AQ6370D Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 445

YOKOGAWA AQ6370D Скачать руководство пользователя страница 36

3-6

IM AQ6370D-01EN

Connecting a USB Storage Device

Supported USB Storage Devices

The instrument supports USB memory (USB card adapters).
You cannot use a USB storage device not recognized by the instrument. If the USB
storage device’s drive is partitioned, only the primary partition (F:) is recognized. If there
are two or more USB storage devices, only the first connected device is recognized.
If you restart the instrument, it the USB storage devices that were connected will still be
recognized.

Connections

Connect the USB storage device to the USB connector on the front panel of the
instrument.

USB

POWER

USB connector

Removing

See section 8.1. (Using the

REMOVE USB STORAGE

soft key.)

CAUTION

Do not remove the USB storage device or turn the power OFF while the USB
storage device access indicator is blinking. This can damage the data on the device
or the device itself.

Connecting with Other Devices

You can use the GP-IB, RS-232C, or Ethernet interface to connect other external
instruments to the AQ. For details, see the

Remote Control User’s Manual,

IM AQ6370C-

17EN.

Note

When connecting a GP-IB instrument such as an external computer, or a CRT or other display
to the instrument, always turn OFF the power to the instrument and the instruments to be
connected first. Leaving the power ON while making connections can damage the equipment.

3.3 Connecting the Device

«
...
34
35
36
37
38
...
»

Содержание AQ6370D






























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды