manualshive.com logo in svg

YOKOGAWA AQ6370D, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ6370D Скачать руководство пользователя страница 33

3-3

IM AQ6370D-01EN

Preparing for Measurement

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

App

Index

3.2  Attaching the Connector Adapter

Attach the optional connector adapter before using the instrument. 

 WARNING

Always turn the power OFF before replacing the connector adapter. The instrument 
has a built-in reference light source for wavelength calibration (when the built-in 
light source specification is -L1), and infrared light is always being output from the 
optical output connector. Never look into the optical output connector. Infrared light 
entering the eyes can cause severe injury and loss of vision.

 CAUTION

•  As there may be dust adhering to calibration output, be sure to clean it before 

attaching the connector adapter. 

•  Do not exhale or blow compressed air into the monochromator from the optical 

input. Doing so may allow dust or other materials to enter the monochromator, 
adversely affecting its optical performance. Also, if debris is adhering to the 
optical components inside the monochromator when a strong light source is 
input, the monochromator may be damaged. 

•  When attaching or removing the connector adapter, carefully insert it 

perpendicularly to the ferrule so as not to damage the ferrule end. 

•  Moving the connector adapter to the right or left or inserting it forcefully can 

damage the ferrule or the connector adapter. 

A connector adapter is required for connecting the optical connector to the AQ6370D.
On products with the /FC, /SC, /RFC, or /RSC option, connector adapters come attached 
to the optical input and calibration light source output on the AQ6370D front panel.
On products without these options, attach a connector adapter appropriate for the optical 
connector.

Note

A different connector adapter is used for OPTICAL INPUT and CALIBRATION OUTPUT. Make 
sure not to use the wrong connector adapter. 

Attachment Procedure

1.

  Confirm that the power is OFF. 

2.

  Open the optical connector cover at the front of the instrument.

3.

  Clean the ferrule edge of the optical I/O section using a swab soaked with a small 

amount of pure alcohol. 

4.

  Insert the connector adapter all the way in. 

5.

  Push the connector adapter’s lock lever down. 

The adapter has been attached correctly if the groove in the lock lever interlocks with the 
latch pin of the optical input/output section. 

Содержание AQ6370D






























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды