manualshive.com logo in svg

YOKOGAWA AQ2200 Series, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ2200 Series Скачать руководство пользователя страница 57

1.10  XFP Interface Module

AQ2200-641 XFP Interface Module

 CAUTION

If an XFP transceiver is not installed, cover the DATA IN and DATA IN input 
terminals with the included protective caps.

French

 ATTENTION

En l’absence d’émetteur-récepteur XFP, couvrir les bornes d’entrée DATA IN et 
DATA IN à l’aide des capuchons de protection fournis.

AQ2200-641

XFP INTERFACE MODULE

REF CLOCK IN

(FROM TRIGGER OUT)

DATA OUT

(TO DATA IN 1)

DATA IN

(FROM DATA OUT)

DATA OUT

DATA IN

(FROM DATA OUT)

XFP

Tx

Rx

XFP transceiver installation slot

Lock lever

Used when installing and 

uninstalling the module.

Lock lever release button

Releases the lock lever.

Signal output indication lamp

This lamp shows the status of the 

transceiver signal output. The lamp 

is lit when the output is on.

Signal output ON/OFF key

Turns the transceiver's optical signal 

(TX) on and off.

Each time this key is pressed, signal 

output switches between on and off.

Inverted data output terminal

Transmits the 10 Gbit/s inverted data. 

Non-inverted data output terminal

Transmits the 10 Gbit/s non-inverted data.

Inverted data input terminal

The 10 Gbit/s inverted data is applied 

to this terminal.

Non-inverted data input terminal

The 10 Gbit/s non-inverted data is 

applied to this terminal.

Fixing screw

When you install the module, tighten 

the screws to fix the module in place.

External synchronization signal input 

terminal

If you want to synchronize the XFP 

interface module with an external clock 

signal and use the module to operate a 

transceiver, apply a reference signal 

that has a frequency that is 1/64 of the 

10 Gbit/s rate to this terminal.

1-24

IM 735101-01EN

Содержание AQ2200 Series
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды