manualshive.com logo in svg

YOKOGAWA AQ2200 Series, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ2200 Series Скачать руководство пользователя страница 43

1.3  Optical Sensor Modules

AQ2200-201 Interface Module

  

AQ2200-201 

INTERFACE 

MODULE 

CHOP 

CW 

ANALOG  OUT 

HEAD 

Lock lever release button

Releases the lock lever.

Modulation indication lamp

The lamp is lit when the light 

modulation is set to CHOP.

CW/CHOP key

Switches the light modulation.

When set to CHOP, modulation is 

performed at the current frequency.

Optical sensor head connector 

Used to connect a cable to the  

optical sensor head.  

(For details, see section 2.5.) 

Lock lever 

Used when installing and uninstalling  

the module. 

ZERO key

Executes the zero-set.

Analog signal output terminal

Transmits the voltage corresponding 

to the input light according to the 

analog output setting.

AQ2200-202 Interface Module

Firmware version 3.05 and later 

  

AQ2200-202

INTERFACE

MODULE

Lock lever release button

Releases the lock lever.

Optical sensor head connector 2

Used to connect a cable to the 

optical sensor head. 

(For details, see section 2.5.)

Lock lever

Used when installing and uninstalling 

the module.

Analog signal output terminal 1

Transmits the voltage corresponding 

to the input light according to the 

analog output setting.

HEAD 2

ANALOG OUT 2

HEAD 1

ANALOG OUT 1

Optical sensor head connector 1

Used to connect a cable to the 

optical sensor head. 

(For details, see section 2.5.)

Analog signal output terminal 2

Transmits the voltage corresponding 

to the input light according to the 

analog output setting.

1-10

IM 735101-01EN

Содержание AQ2200 Series
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды