manualshive.com logo in svg

YOKOGAWA AQ2200 Series, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ2200 Series Скачать руководство пользователя страница 151

5.9  AQ2200-231/241 Optical Sensor Head

Performance and Functional Specifications

Item

Specifications

AQ2200-231

AQ2200-241

Photo sensor element

InGaAs, 5 mm diameter

Si, 10 mm diameter

Measurement wavelength range

800 to 1700 nm

400 to 1100 nm

Power range

CW light: –90 to +10 dBm

CHOP light: –90 to +7 dBm

Minimum display resolution

1/10000

Applicable optical fiber

 1

≤ 100/140 μm (SI), NA ≤ 0.3

≤ 200/230 μm (SI), NA ≤ 0.5

Uncertainty at reference conditions

±2%

 2

±2.5%

 3

Total uncertainty

±3.5% ± 50 pW

 4

±5% ± 50 pW

 5

Polarization dependence

0.025 dBp-p or less

 6

Nonlinearity

±0.015 dB ± 50 pW

 7

±0.05 dB ± 50 pW

 8

Noise level

 9,  10

CW light

50 pW or less

CHOP light

50 pW or less

Averaging time (minimum)

100 μ

s

Analog output

AUTO mode

Approx. 0 to 2 V, proportional to the measurement power (W) for each power range

LINEAR mode

Approx. 0 to 2 V, proportional to the range set for measurement power (W)

LOG mode

Approx. 0 to 2 V, proportional to the range set for measurement power (dBm)

Connector type

Mini plug

Output impedance

Approx. 1 kΩ

Optical connector

 11

AQ9335C connector adapter

Logging measurement

Measurement power range

Fixed

Minimum data sampling interval

100 μ

s

Maximum number of data samples

20000

Stability measurement

Minimum data sampling interval

100 ms

Maximum number of data samples

20000

Maximum measurement time

99 days

General Specifications

Item

Specifications

Operating conditions

The same as the frame controller’s operating environment

Temperature and humidity for storage

Ambient temperature

–20 to +60°C

Ambient humidity

20 to 80% RH (no condensation)

External dimensions

61 (W) × 42 (H) × 100 (D) mm (excluding protrusions)

Weight

Approx. 0.3 kg

*  All values in the specifications assume a warm-up period of one hour.
1  Depends on the AQ9335C

*

 and the diameter of the light receiving sensor. You can also perform atmospheric light 

measurements by removing the connector adapter.

2  Reference conditions:

  •  Power level: 100 μW (–10 dBm), CW light

  •  Wavelength: 1310 ± 20 nm
  •  Light source spectrum width: 10 nm or less
  •  Ambient temperature: 23 ± 2°C
  •  Optical fiber: SM (ITU-T G.652)
  •  Optical connector: FC/PC
  •  Wavelength setting error: 0.5 nm or less
  •   Changes to the measuring instrument due to the passage of time are not included in these conditions. Add 0.5% for each 

year since the last calibration.

5-14

IM 735101-01EN

Содержание AQ2200 Series
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды