manualshive.com logo in svg

YOKOGAWA AQ2200 Series, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ2200 Series Скачать руководство пользователя страница 138

5.1  AQ2211/AQ2212 Frame Controller

Performance and Functional Specifications

Item

Specifications

Number of slots

AQ2211: 3

AQ2212: 9

Display

Color LCD, 320 × 240 dots

Storage

USB storage

USB Mass Storage Class flash memory. See “USB (for peripheral devices).”

Output format

Setup parameters

Proprietary format

Measurement data

Log data: 

 .csv

Stability data: 

 .csv

Wavelength sweep data:  .csv

BERT log data: 

 .txt

Screen captures: 

 .bmp, .jpg, and .png

Interface

GP-IB

Electrical and mechanical 

specifications

Complies with IEEE488

 1

Functional specifications SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT0, and C0

Protocol

Complies with IEEE488.2

Code

ISO (ASCII)

Mode

Addressable mode

Addresses

0 to 30

Clearing remote mode

The LOCAL soft key can be pressed to clear remote mode (except during Local 

Lockout).

Ethernet

Number of ports

1

Connector type

RJ-45

Electrical and mechanical 

specifications

Complies with IEEE802.3

 1

Transmission system

Ethernet (100BASE-Tx)

Transfer rate

100 Mbps max.

Communication protocol TCP/IP

Supported services

DHCP and remote control. (Remote control supports a maximum of five users.)

Ports

0 to 65535; port 10001 is reserved for the TMCTL protocol

USB

(For connecting 

to a PC)

Number of ports

1

Connector type

USB type B (receptacle)

Electrical and mechanical 

specifications

Complies with USB Rev 1.1

 1

Data rate

12 Mbps max.

Supported protocols

USB-TMC

Supported services

Remote control

PC system requirements The PC must be running Windows XP, or Windows Vista (32/64 bits), Windows 7 

(32/64 bits), Windows 8 (32/64 bits) and must have a standard USB port.

2

USB

(For peripheral 

devices)

Number of ports

1

Connector type

USB type A (receptacle)

Electrical and mechanical 

specifications

Complies with USB Rev 2.0

 1

Data rate

480 Mbps max.

Compatible devices

USB Mass Storage Class flash memory

Number of devices that 

can be connected

1

Power supply

5 V, 500 mA

Maximum usable capacity 2 TB (Disk partition style: MBR, Format: FAT32/FAT16)

Trigger unit

Connector type

BNC

 1

Trigger in

TTL level input

Input pulse width: 50 μs or greater

Input impedance: approx. 5 kΩ

Trigger out

TTL level output

Output pulse width: approx. 50 μs

Output impedance: approx. 100 Ω

Interlock connector 

unit

Connector type

BNC

 1

Contact input

1  Use cables of 3 m or less in length.

2  A separate driver is required.

5-1

IM 735101-01EN

Specifications

Chapter 5  Specifications

1

2

3

4

5

Index

Содержание AQ2200 Series
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды