manualshive.com logo in svg

YOKOGAWA AQ2200 Series, Руководство пользователя

Поделиться
Скачать
YOKOGAWA AQ2200 Series Скачать руководство пользователя страница 101

3.8  SG Module

 CAUTION

•  Before removing modules from the frame controller, turn the output off.
•  Before turning the frame controller off, turn the output off.
•  Before connecting cables to or disconnecting cables from the I/O terminals, turn 

the output off.

•  Before connecting cables to the I/O terminals, tighten the connectors at a 

specified torque using a torque wrench.

•  Do not leave the REF OUT and 10 MHz REF OUT terminals open. Always 

terminate them with 50 Ω loads, such as the included terminators. Likewise, 

always terminate the cables that are connected to these output terminals with 

50 Ω loads.

•  Do not apply a signal that is greater than the specified maximum input voltage to 

the input terminals.

•  Before connecting the unit to the DUT, turn the output off.
•  Always use the specified connector to connect this module’s I/O terminals. Using 

unspecified connectors to connect the I/O terminals may cause damage to the 
terminals and the connectors.

•  When attaching connectors to the I/O terminals, always connect them straight, 

not at an angle. Attaching connectors to the I/O terminals at an angle may cause 
damage to the I/O terminals or the connectors’ core wires.

•  Do not apply external voltage to the output terminals.

French

 ATTENTION

•  Avant de retirer les modules du contrôleur, mettre la sortie hors tension.
•  Avant de mettre le contrôleur hors tension, mettre la sortie hors tension.
•  Avant de brancher les câbles aux bornes d’E/S ou de les débrancher, mettre la 

sortie hors tension.

•  Avant de brancher les câbles aux bornes d’E/S, serrer les connecteurs selon le 

couple spécifié à l’aide d’une clé dynamométrique.

•  Ne pas laisser les bornes REF OUT et REF OUT de 10 MHz ouvertes. Toujours les 

raccorder à des charges de 50 Ω, telles que les bornes incluses. De même, toujours 
raccorder les câbles connectés à ces bornes de sortie à des charges de 50 Ω.

•   Ne pas appliquer de signal supérieur à la tension d’entrée maximum spécifiée 

aux bornes d’entrée.

•  Avant de raccorder l’unité au DUT, mettre la sortie hors tension.
•   Toujours utiliser le connecteur spécifié pour le raccordement des bornes d’E/S 

de ce module. L’utilisation de connecteurs non conformes aux spécifications 
pour le raccordement des bornes d’E/S risque de provoquer des dommages aux 
bornes et aux connecteurs.

•   Toujours brancher les connecteurs aux bornes d’E/S de manière droite et non 

inclinée pour éviter d’endommager ces dernières ou d’endommager les fils des 
connecteurs.

•  Ne pas appliquer de tension externe aux bornes de sortie.

3-15

IM 735101-01EN

External Input and Output

1

2

3

4

5

Index

Содержание AQ2200 Series
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды