YOKOGAWA AQ1215A Скачать руководство пользователя страница 140

Страница: 140 / 282

7-9

IM AQ1210-01EN

Using the Utility Feature

App

Index

Using the VLS from the OTDR Screen (utility button)

Displaying the OTDR Screen

Press

MENU

to display the MENU screen.

Tap

OTDR

to display the OTDR screen.

MENU screen

OTDR Screen

Tap

VLS

to display the visible light source screen.

Visible Light

Source Screen

Drag to move the visible

light source screen.

Set the

modulation mode

(CW, 2Hz).

Turns the light output on and off

The output turns on or off each time you tap the button.

VLS button

Starts the visible light source screen

Returns the waveform display area to

its original condition

The example of the OTDR screen shows

the waveform display area expanded.

Note

If the VLS button is not displayed, see “Changing a Utility Button” under “Using the Light Source from the
OTDR Screen (utility button)” in section 7.1.

7.2 Using the Visible Light Source (/VLS option)

Содержание AQ1215A



























































































































































































































































































Результаты поиска

Содержание AQ1215A

Отзывы:

Похожие инструкции для AQ1215A

Бренды по названию

Популярные бренды

YOKOGAWA AQ1215A, Руководство пользователя

Результаты поиска

Содержание AQ1215A

Отзывы:

Похожие инструкции для AQ1215A

Бренды по названию

Популярные бренды