YOKOGAWA 701715 Скачать руководство пользователя страница 399

Страница: 399 / 454

15-5

IM 701730-01E

Other Operations

15.3 Measuring the Offset Voltage and Applying the

Offset Voltage to the Computed Results

Procedure

ACTION

DELAY

X - Y

MENU

PHASE

SEARCH

HORIZONTAL

VERTICAL

TRIGGER

TRIG D

HELP

ESC

SELECT

RESET

SIMPLE

MODE

POSITION

MATH

MISC

FILE

CLEAR

TRACE

HISTORY

MEASURE

SETUP

PRESET

DISPLAY

CURSOR

POWER

COPY IMAGE SAVE

SHIFT

ZOOM

GO/NO-GO

ENHANCED

ACQ

START/STOP

SNAP

SHOT

V DIV

TIME DIV

• To exit the menu during operation, press

ESC

located above the soft keys.

• For a description of the operation using a USB

keyboard or a USB mouse, see section 4.3.

Press the

MISC

Press the

System Cnfg

soft key to display a configuration menu.

Press the

Offset Cancel

soft key to select ON or OFF.

The default setting is OFF.

Explanation

The offset value that is specified for each channel can be subtracted from the input

signal and used for computation and automated measurement.

OFF: The offset value is not applied to computed results and the results of automated

measurements.

Waveform is observed without subtracting the offset voltage (DC voltage) from

the input signal.

The vertical position of the screen corresponds to the offset voltage.

ON:

The offset value is applied to computed results and the results of automated

measurements.

The offset value specified for each channel can be used to subtract the offset

voltage (DC voltage) from the input signal for waveform observation. The vertical

position is set to 0 V.

Note

The Offset Cancel setting applies to all channels.

To specify whether to cancel or not cancel the offset voltage for each channel separately, use

the linear scaling function.

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды