YOKOGAWA 701715 Скачать руководство пользователя страница 394

Страница: 394 / 454

14-6

IM 701730-01E

14.3 Video Signal Output (VIDEO OUT (VGA))

CAUTION

• Connect the cable after turning OFF the instrument and the monitor.

• Do not short the VIDEO OUT (VGA) terminal or apply external voltage to it.

Doing so can cause damage to the instrument.

Video Output Terminal

The instrument display can be output to a monitor through the RGB output. Connectable

monitors are VGA monitors or multi-sync monitors capable of displaying VGA.

Pin No.

Signal Name

Description

Red

0.7 Vp-p

Green

0.7 Vp-p

Blue

0.7 Vp-p

GND

Horizontal sync signal

Approx. 31.3 kHz, TTL negative logic

Vertical sync signal

Approx. 60 Hz, TTL negative logic

VIDEO OUT (VGA)

D-Sub 15-pin receptacle

Connecting to the Monitor

Turn OFF the instrument and monitor.

Connect the instrument and the monitor using an analog RGB cable.

The screen of the instrument appears on the monitor when both the instrument and

the monitor are turned ON.

Note

•

The RGB video signal is constantly output from the VIDEO OUT (VGA) terminal.

•

The monitor screen may flicker if the instrument or another instrument is brought close to the

monitor.

•

The edge of the screen may drop out depending on the monitor type.

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

YOKOGAWA 701715, Руководство пользователя, Страница: 394 / 454

Результаты поиска

Содержание 701715

Отзывы: