YOKOGAWA 701715 Скачать руководство пользователя страница 383

Страница: 383 / 454

13-47

IM 701730-01E

Ethernet Communications (Optional)

13.9 Checking the Presence of the Ethernet

Interface (Optional) and the MAC Address

Procedure

ACTION

DELAY

X - Y

MENU

PHASE

SEARCH

HORIZONTAL

VERTICAL

TRIGGER

TRIG D

HELP

ESC

SELECT

RESET

SIMPLE

MODE

POSITION

MATH

MISC

FILE

CLEAR

TRACE

HISTORY

MEASURE

SETUP

PRESET

DISPLAY

CURSOR

POWER

COPY IMAGE SAVE

SHIFT

ZOOM

GO/NO-GO

ENHANCED

ACQ

START/STOP

SNAP

SHOT

V DIV

TIME DIV

• To exit the menu during operation, press

ESC

located above the soft keys.

• For a description of the operation using a USB

keyboard or a USB mouse, see section 4.3.

Press the

MISC

. The MISC menu appears.

Press the

Overview

soft key. The Overview window opens.

Pressing a panel key other than the

Overview

soft key clears the Overview

window.

When Ether: Yes(/C10) appears for the Option item in the Overview window, this

indicates that the Ethernet interface is installed.

The information displayed on the right (MAC:000064_841_002 in the example) is

the MAC address.

Note

•

Ether: Yes(/C10) is displayed only if the Ethernet interface option is installed.

•

If XXXXXX_XXX_XXX is displayed for the MAC address, contact the dealer from which you

purchased the instrument.

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды