YOKOGAWA 701715 Скачать руководство пользователя страница 371

Страница: 371 / 454

13-35

IM 701730-01E

Ethernet Communications (Optional)

Displaying the Measurement Trend of Waveform Parameters

Before using this function, check that the communication interface of the instrument is

set to Network (see page 13-23).

Click the Measurement Trend icon on the Web server window. The Measurement Trend

window in which the trend display of the waveform parameter values can be set appears.

Web Server Window

Measurement Trend Window

Control panel

Note

•

This function retrieves the selected waveform parameter values at the selected retrieve

interval from the instrument into the PC and displays the trend. To display the retrieved

measurement values and trend, Microsoft Excel 97 or later must be installed on the PC.

•

If the measured value of a waveform parameter is not a normal number (Not A Number), the

cell displaying the measured value on Microsoft Excel is set to blank.

•

This function cannot be used in roll mode.

13.7 Using the Web Server Function

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды