YOKOGAWA 701715 Скачать руководство пользователя страница 339

Страница: 339 / 454

13-3

IM 701730-01E

Ethernet Communications (Optional)

13.2 Setting Up the TCP/IP

Procedure

ACTION

DELAY

X - Y

MENU

PHASE

SEARCH

HORIZONTAL

VERTICAL

TRIGGER

TRIG D

HELP

ESC

SELECT

RESET

SIMPLE

MODE

POSITION

MATH

MISC

FILE

CLEAR

TRACE

HISTORY

MEASURE

SETUP

PRESET

DISPLAY

CURSOR

POWER

COPY IMAGE SAVE

SHIFT

ZOOM

GO/NO-GO

ENHANCED

ACQ

START/STOP

SNAP

SHOT

V DIV

TIME DIV

• To exit the menu during operation, press

ESC

located above the soft keys.

• In the procedural explanation below, the term

jog

shuttle & SELECT

refers to the operation of

selecting/setting items and entering values using

the

jog shuttle

and

SELECT

and

RESET

keys.

For details on this operation, see sections 4.1 and

4.2.

• For a description of the operation using a USB

keyboard or a USB mouse, see section 4.3.

Entering the TCP/IP Setup Menu

Press the

MISC

key. The MISC menu appears.

Press the

Network

soft key. The Network menu appears.

Press the

TCP/IP Setup

soft key. The TCP/IP Setup dialog box opens.

Turning DHCP ON and OFF

Use

jog shuttle & SELECT

to set DHCP to ON or OFF.

•

If you select OFF, proceed to step 5.

•

If you set DHCP to ON, you do not have to set the IP address, subnet mask, default

gateway below. If you select DNS, proceed to step 8. If DNS is not set, check the network

cable connection and power-cycle the instrument. The IP address, subnet mask, and

default gateway are automatically configured.

DHCP

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды