YOKOGAWA 701715 Скачать руководство пользователя страница 233

Страница: 233 / 454

10-33

IM 701730-01E

Analyzing and Searching Waveforms

10.5 Cursor Measurements

Moving Cursors

Press the

Cursor1/Cursor2

soft key to set the jog shuttle control to Cursor1,

Cursor2, or both Cursor1 and Cursor2.

•

Select Cursor1 to move Cursor1.

•

Select Cursor2 to move Cursor2.

•

If you select both Cursor1 and Cursor2, you can move Cursor1 and Cursor2 horizontally

without changing the spacing between the two. The value of the digit being specified by

Cursor1 changes.

When X-Y waveforms are not displayed.

When X-Y waveforms are displayed.

Turn the

jog shuttle

to move the cursor.

Jumping the Cursor to the Zoom Waveform Display Frame (When X-Y Waveforms

Are Not Displayed)

Press the

Cursor Jump

soft key. The Cursor Jump menu appears.

Press the

C1 to Z1

C1 to Z2

C2 to Z1

, or

C2 to Z2

soft key to select the cursor

and the jump destination.

10.

Press the

Jump Exec

soft key. The cursor jumps to the specified zoom waveform

display frame.

Measuring Waveforms Using Marker Cursors

Press

CURSOR

. The CURSOR menu appears.

Selecting the Marker Cursor

Press the

Type

soft key. The Type menu appears.

Press the

Marker

soft key.

H&V

can also be displayed on products with firmware version 2.09 or later.

When X-Y waveforms are displayed, Degree is not available.

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды