YOKOGAWA 701715 Скачать руководство пользователя страница 212

Страница: 212 / 454

10-12

IM 701730-01E

Explanation

This section explains the setup procedures for searching history waveforms that meet or

do not meet the specified search parameter conditions.

Search Parameters

You can register up to four search parameters, Param1 to Param4. For each search

parameter, you can set the search conditions below. You can also set whether to use

AND or OR logic of the search conditions of the four search parameters to perform the

search (see “Search Logic” described later).

• Status of the search parameter for the searched waveform

• Target waveform/search measurement item

• Determination range of the measured value of the search measurement parameter

• Search range

Status of the Search Parameters for the Searched Waveform: Condition

You can select from the following.

OFF: No search is performed.

IN:

Searches for waveforms whose measured value of the search and measurement

parameter is within the determination range of the specified search parameter.

Search is also made on boundary values.

OUT: Searches for waveforms whose measured value of the search and measurement

parameter is not within the determination range of the specified search

parameter.

Selecting the Search Target Waveform/Search Measurement Item

You can select the target waveform and the measurement parameter to be used as a

search condition. If a waveform that meets the search condition is found, other history

waveforms at the same time as the found waveform are also displayed.

Waveform to Search

• For the DL1735E/DL1740E/DL1740EL

You can select the target waveform from CH1 to CH4, Math1, and Math2.

• For the DL1720E

You can select from CH1 to CH2, and Math1.

Search Measurement Items

Same as the measurement parameters of the automated measurement of waveform

parameters. See section 10.6.

Determination Range of the Measured Value of the Search Measurement

Parameter

You can set the upper and lower limits of the determination range. The selectable range

is –9.9999E+30 to 9.9999E+30. The upper limit (Upper) must be greater than or equal to

the lower limit (Lower)

Search Logic

You can select the AND logic or OR logic of the search conditions of the four search

parameters in performing the search.

AND: Searches for waveforms that meet all search conditions of Param1 to Param4.

OR:

Searches for waveforms that meet one of the search conditions of Param1 to

Param4.

Search Range: T-Range1/T-Range2

The selectable range is

5 divisions, and the resolution is ten divisions

display record

length. The right end of the search range (T-Range2) must be greater than or equal to

the left end of the search range (T-Range1).

10.3 Searching the History Waveforms Using Automatic Measurement of Parameters (History Search)

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды