YOKOGAWA 701715 Скачать руководство пользователя страница 207

Страница: 207 / 454

10-7

IM 701730-01E

Analyzing and Searching Waveforms

Selecting the Search Logic

19.

Press the

Logic

soft key to select AND or OR.

Executing/Aborting the Search

20.

Press the

Search Exec

soft key. The search is executed, and the words Search

Exec change to Search Abort.

To abort the search, press the

Search Abort

soft key. The search is aborted, and

the words Search Abort change to Search Exec.

Displaying the Found Waveform

21.

Press

ESC

. The screen returns to the HISTORY menu.

22.

Display the waveform according to the procedure given in section 10.1.

The history map lists the record numbers and time stamps of the searched

waveforms.

Resetting the Search Results

23.

Set the Search Mode to OFF in the HISTORY menu, or turn OFF Zone1 to Zone4

and execute the search. The search result is reset.

Explanation

This section explains the setup procedures for searching history waveforms that pass or

do not pass a specified search zone.

Search Zone: Select Zone

You can register up to four search zones, Zone1 to Zone4. For each search zone, you

can set the search conditions below. You can also set whether to use AND or OR logic

of the search conditions of the four search parameters to perform the search (see

“Search Logic” described later).

• Status of the search parameter for the searched waveform

• Waveform to search

• Search zone range

Status of the Search Parameter for the Searched Waveform: Condition

You can select the condition of the target waveform to be searched in the search zone.

OFF: No search is performed.

IN:

Searches waveforms that pass through the specified search zone. Also searches

cases when the waveforms pass through the boundary lines.

OUT: Searches waveforms that do not pass through the specified search zone.

Waveform to Search: Source

You can select the search target waveform. If a waveform that meets the search

condition is found, other history waveforms at the same time as the found waveform are

also displayed.

• For the DL1735E/DL1740E/DL1740EL

You can select the target waveform from CH1 to CH4, Math1, and Math2.

• For the DL1720E

You can select from CH1 to CH2, and Math1.

10.2 Searching the History Waveforms Using Zones (History Search)

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды