YOKOGAWA 701715 Скачать руководство пользователя страница 143

Страница: 143 / 454

6-28

IM 701730-01E

6.12 Setting the OR Trigger (ENHANCED)

<For a description of this function, refer to page 2-10.>

Procedure

ACTION

DELAY

X - Y

MENU

PHASE

SEARCH

HORIZONTAL

VERTICAL

TRIGGER

TRIG D

HELP

ESC

SELECT

RESET

SIMPLE

MODE

POSITION

MATH

MISC

FILE

CLEAR

TRACE

HISTORY

MEASURE

SETUP

PRESET

DISPLAY

CURSOR

POWER

COPY IMAGE SAVE

SHIFT

ZOOM

GO/NO-GO

ENHANCED

ACQ

START/STOP

SNAP

SHOT

V DIV

TIME DIV

• To exit the menu during operation, press

ESC

located above the soft keys.

• In the procedural explanation below, the term

jog

shuttle & SELECT

refers to the operation of

selecting/setting items and entering values using

the

jog shuttle

and

SELECT

and

RESET

keys.

For details on this operation, see sections 4.1 and

4.2.

• For a description of the operation using a USB

keyboard or a USB mouse, see section 4.3.

Setting the Trigger Type

Press

ENHANCED

. The ENHANCED menu appears.

Press the

Type

soft key. The Type menu appears.

Press the

soft key.

Setting the Window

Press the

Window

soft key and select ON or OFF.

•

If set to OFF, a trigger is activated on the OR logic of the edge of each channel.

•

If set to ON, a trigger is activated on the OR logic of the window condition of each channel.

Setting Slope of the Edge Trigger of Each Channel

5.-

Press the

Set Pattern

soft key. The Set Pattern dialog box opens.

The settings related to CH3 and CH4 are not displayed on the DL1720E.

Use

jog shuttle & SELECT

to set the slope of the edge trigger of each channel to

, , or — (IN, OUT, or —. if Window is ON).

When Window is OFF

When Window is ON

You can select the
slope of the edge for
each channel.

Select IN, OUT, or X for
the window condition
of each channel.

Press

ESC

. The Set Pattern dialog box closes.

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды