YOKOGAWA 701715 Скачать руководство пользователя страница 135

Страница: 135 / 454

6-20

IM 701730-01E

6.10 Setting the Pattern Trigger (ENHANCED)

<For a description of this function, refer to page 2-9.>

Procedure

ACTION

DELAY

X - Y

MENU

PHASE

SEARCH

HORIZONTAL

VERTICAL

TRIGGER

TRIG D

HELP

ESC

SELECT

RESET

SIMPLE

MODE

POSITION

MATH

MISC

FILE

CLEAR

TRACE

HISTORY

MEASURE

SETUP

PRESET

DISPLAY

CURSOR

POWER

COPY IMAGE SAVE

SHIFT

ZOOM

GO/NO-GO

ENHANCED

ACQ

START/STOP

SNAP

SHOT

V DIV

TIME DIV

• To exit the menu during operation, press

ESC

located above the soft keys.

• In the procedural explanation below, the term

jog

shuttle & SELECT

refers to the operation of

selecting/setting items and entering values using

the

jog shuttle

and

SELECT

and

RESET

keys.

For details on this operation, see sections 4.1 and

4.2.

• For a description of the operation using a USB

keyboard or a USB mouse, see section 4.3.

Setting the Trigger Type

Press

ENHANCED

. The ENHANCED menu appears.

Press the

Type

soft key. The Type menu appears.

Press the

Pattern

soft key.

Setting the Status and Condition

Press the

Set Pattern

soft key. The Set Pattern dialog box opens.

The settings related to CH3 and CH4 are not displayed on the DL1720E.

• Activating a Trigger Only on the Status Pattern

Use

jog shuttle & SELECT

to set Clock CH to None.

These are not displayed on the DL1720E.

Use

jog shuttle & SELECT

to select H, L, or X for the status of each channel.

Use

jog shuttle & SELECT

to set Condition to Enter or Exit.

Proceed to step 9.

Select H, L, or X for the status of each
channel.

Select None for the clock channel.

Set Condition to Enter or Exit.

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды