YOKOGAWA 701210 Скачать руководство пользователя страница 65

Страница: 65 / 747

2-27

IM 701210-05E

Explanation of Functions

2.3 Setting the Trigger

Trigger Mode <Section 6.1>

Sets the conditions for updating the displayed waveforms. The following six trigger

modes are available.

Auto Mode

If a trigger occurs within a specified amount of time (approximately 50 ms, referred to as

the timeout period), the displayed waveforms are updated. If a trigger is not activated

within the timeout period, the displayed waveforms are automatically updated.

Auto Level Mode

Within the timeout period (approximately 1 s), the waveforms are displayed in the same

fashion as in the auto mode. If a trigger is not activated within the timeout period, then

the center value of the amplitude of the trigger source is detected, and the trigger level is

changed to that value. A trigger is activated using the new value, and the displayed

waveforms are updated.

1/2 the amplitude

Trigger level

Amplitude

Normal Mode

The displayed waveforms are updated only when a trigger occurs. The displayed

waveforms are not updated if a trigger does not occur.

Single Mode

When a trigger is activated, displayed waveforms are updated only once, then

acquisition stops. This mode is useful when you are observing a single-shot signal.

Single (N) Mode (Sequential Store Function)

This mode is selected when using the sequential store function (see section 7.5).

Waveforms are acquired and stored in different memory areas each time a trigger is

activated the specified number of times. Then, acquisition is stopped, and all the

acquired waveforms are displayed. Acquired waveforms can be displayed together, or

they can be displayed individually. This mode is useful when you wish to detect sudden

abnormalities in a waveform.

1st acquisition

2nd acquisition

nth acquisition

Log Mode

In this mode, the trigger settings are disabled. The specified record length of data is

acquired once when acquisition is started, and the displayed waveforms are updated.

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 65 / 747

Результаты поиска

Содержание 701210

Отзывы: