YOKOGAWA 701210 Скачать руководство пользователя страница 47

Страница: 47 / 747

2-9

IM 701210-05E

Explanation of Functions

2.2 Setting the Horizontal and Vertical Axes

Probe Type <Section 5.6>

For voltage (current) measurement, a probe is normally used in connecting the circuit

being measured to the measurement input terminal. Using a probe has the following

advantages.

• Prevents disturbing the voltage and current of the circuit being measured.

• Inputs the signal with no distortion.

• Expands the voltage range that can be measured by the DL750/DL750P.

When using a probe, the attenuation or current-to-voltage conversion ratio setting on the

module must be set equal to the probe attenuation on the DL750/DL750P so that the

measured voltage can be read directly.

The probe attenuation of each probe (accessory sold separately) is set as follows:

• Voltage probe (700929):

10:1

• Current probe (700937/701933):

10 A:1 V

• Current probe (701930/701931):

100 A:1 V

• Voltage differential probe (700924):

1000:1, 100:1

• 10:1 passive probe for the DL750/DL750P: 10:1

The DL750/DL750P has the following attenuation settings: 1:1, 10:1, 100:1, 1000:1, 10

A:1 V

, and 100 A :1 V

. If you are using a probe other than the ones provided as

accessories (sold separately), set the attenuation ratio on the DL750/DL750P according

to the attenuation of the probe.

1. Output voltage rate: 0.1 V/A
2. Output voltage rate: 0.01 V/A

Note

Use a probe that matches the input capacity of each module. Otherwise, the capacity cannot
be adjusted.

Bandwidth Limit <Section 5.7>

The bandwidth can be limited on each module. By limiting the bandwidth, you can

eliminate the noise components from the input signal for waveform observation.

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 47 / 747

Результаты поиска

Содержание 701210

Отзывы: