YOKOGAWA 701210 Скачать руководство пользователя страница 322 | Manualshive

Страница: 322 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 322

9-3

IM 701210-05E

Recording in Recorder Mode (Realtime Recording) (Only on the DL750P)

9

7.

Move the release lever to the HOLD position

(down direction). The printing will fail with an error

message, if the release arm is in the FREE

position during operation.

8.

Close the printer cover. Push the printer cover

down firmly until it clicks into place.

Note

•

If you are reusing an old roll paper that had been taken out, the roll paper can be inserted
easily by cutting the leading edge at an angle.

•

Before closing the printer cover, be sure to set the release arm position to HOLD.

•

After loading the roll paper, make sure that the paper is feeding properly according to the
steps given below. If the paper is not being fed evenly, continue to feed the paper for
approximately 30 cm. The paper will straighten out.

Feeding the Paper

You can feed the paper to check whether the roll paper has been loaded properly or to

skip dirty sections.

FILE

SHIFT

HELP

MISC

NUM KEY

PROTECT

IMAGE

SAVE

PRINT

FEED

SNAPSHOT CLEAR TRACE

MENU

VOICE MEMO

MENU

Feeding Paper with the FEED Key

1.

Press the

FEED

key. Each time the key is pressed, the paper is fed out by 15

mm.

Feeding Paper from the PRINT Menu

1.

Press

SHIFT+PRINT

.

2.

Press the

Print to

soft key. The printer selection menu appears. (Net Print

appears only when the Ethernet interface option is installed.)

3.

Press the

Printer

soft key.

4.

Press the

Paper Feed

soft key. Each time the key is pressed, the paper is fed

out by 15 mm.

Release lever: HOLD

9.1 Loading the Roll Paper into the DL750P Built-in Printer

«
...
320
321
322
323
324
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов