YOKOGAWA 701210 Скачать руководство пользователя страница 306

Страница: 306 / 747

8-10

IM 701210-05E

Explanation

Zoomed waveforms of two locations can be displayed simultaneously (dual zoom). You

can also specify which channels to zoom. Zooming is not possible if the number of

points displayed on the screen is less than or equal to 10 points (less than or equal to 50

for FFT waveforms).

Selecting the Display Mode of Zoomed Waveforms

Main:

Displays only the main (unzoomed) waveform.

Z1 Only:

Displays only the zoomed waveform of zoom box Z1.

Z2 Only:

Displays only the zoomed waveform of zoom box Z2.

Main&Z1:

Displays the main waveform in the top window and zoomed waveform of

zoom box Z1 in the bottom window.

Main&Z2:

Displays the main waveform in the top window and zoomed waveform of

zoom box Z2 in the bottom window.

Z1&Z2:

Displays the zoomed waveform of zoom box Z1 in the top window and

the zoomed waveform of zoom box Z2 in the bottom window.

Main&Z1&Z2:

Displays the main waveform in the top window, the zoomed waveform of

zoom box Z1 in the lower left window and the zoomed waveform of zoom

box Z2 in the lower right window.

Note

On the DL750P, the range of zoom box Z2 can be printed expanded on the built-in printer
(zoom print). For details, see section 12.2.

Selecting the Zoomed Trace: Allocation

The traces whose Allocation is turned ON are zoomed. If the allocation is OFF, the trace

is not zoomed. You cannot allocate channels whose display is turned OFF.

Display Format of Zoomed Waveforms

Similar to the main waveform, 6 types (Main

, Single, Dual, Triad, Quad, Octal, Hexadecimal) of

display formats are available. You cannot set different formats for Z1 and Z2.

1. Selecting Main results in the same format as Main Format in the DISPLAY menu .

Zoom Rate: Z1 Mag/Z2 Mag

• Sets the T/div of the zoom waveform display area.

• If the time base is set to an external clock signal, select the magnification from the

following:

2.5,

10,

25,

50,

100,

250,

500,

1000,

2500, ... , ten-fold multiples of

1, 2.5, 5, up to

1000000

• The maximum zoom rate varies depending on the display record length.

Maximum zoom rate: Display record length

• The maximum magnification during realtime recording with respect to the display

record length of the main waveform is as follows:

Main Waveform Record Length

Record Length of the Zoom Window

1 MW to 10 MW

250 kW

25 MW

500 kW

50 MW

1 MW

1000 MW or more

2.5 MW

• The display record length does not necessarily match the record length.

For details on the display record length, see appendix 1, “Relationship between the

Time Axis Setting, Sample Rate and Record Length.”

• You can set different zoom rates for Z1 and Z2 (zoomed waveform of two locations).

8.5 Zooming the Waveform

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 306 / 747

Результаты поиска

Содержание 701210

Отзывы: