YOKOGAWA 701210 Скачать руководство пользователя страница 261

Страница: 261 / 747

6-43

IM 701210-05E

Triggering

6.17 Setting the Wave Window Trigger (ENHANCED)

The time difference from the abnormal waveform to the trigger point varies depending on

the reference cycle as follows. When the frequency of the trigger is low, the time

difference from the abnormal waveform to the trigger point is 0 cycles in most cases.

Reference Cycle

Time Difference

1 cycle

0 or 1 cycle

2 cycles

0, 1 or 2 cycles

4 cycles

0, 1, 2, 3, or 4 cycles

When using the wave window trigger, it is recommended that a pretrigger equal to the

reference cycle be specified. This allows abnormal waveforms to be observed even

when the above phenomenon occurs.

Selecting the Trigger Condition

ON:

Use the channel as a target channel for the wave window trigger.

OFF: Do not use the channel as a target channel for the wave window trigger.

• Cycle Frequency

Set the frequency of the measured power supply in the range of 40 to 1000 Hz. The

resolution is 0.1 Hz. The default value is 50 Hz.

If the actually frequency is within

10% of the specified value, it is automatically

tracked.

• Reference Cycle

Select how many waveforms before the current waveform are used to create the

realtime template (wave window).

1 (1 waveform), 2 (2 waveforms), or 4 (4 waveforms)

The waveforms of the specified number of reference cycles are used to create the

realtime template.

• Sync. Ch, Level, and Hys

Select the channel used to detect the waveform determination start point of the wave

window trigger. Select the synchronization channel from Auto or CH1 to CH16.

If a setting other than Auto was selected, set the level and hysteresis of the

synchronization channel.

If set to Auto, the synchronization channel is automatically set using the following

conditions.

Target channel:

Channel with the smallest channel number among the target

channels of the wave window trigger.

Level:

1/2 the peak-to-peak value over 0.5 s after starting the waveform

acquisition.

Hysteresis:

Same as the hysteresis of an edge trigger (see section 6.5)

If a setting other than Auto was selected, set the level and hysteresis of the

synchronization channel.

• Setting the Level

The selectable range of the level is the same as that of the simple trigger.

• Setting the Hysteresis

Sets a width to the trigger level so that triggers are not activated by small changes in

the trigger signal. Select the trigger hysteresis from

, and

For details, see “Setting the Trigger Hysteresis” in section 6.5.

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 261 / 747

Результаты поиска

Содержание 701210

Отзывы: