YOKOGAWA 701210 Скачать руководство пользователя страница 23

Страница: 23 / 747

Part 1:xii

IM 701210-05E

Conventions Used in This Manual

Unit

k: Denotes 1000.

Example: 100 kS/s (sampling rate)

K: Denotes 1024.

Example: 720 KB (storage capacity of a floppy disk)

Displayed Characters

• Bold characters used in the procedural explanations indicate characters that are

marked on the panel keys or the characters of the soft keys displayed on the screen

menu.

• The SHIFT + xxx key refers to first pressing the SHIFT key (the indicator above the

SHIFT key lights), and then pressing the xxx key. The menu marked in purple below

the pressed key appears on the screen.

Safety Markings

The following markings are used in this manual.

Improper handling or use can lead to injury to the user or

damage to the instrument.

This symbol appears on the

instrument to indicate that the user must refer to the user’s

manual for special instructions. The same symbol appears

in the corresponding place in the user’s manual to identify

those instructions. In the manual, the symbol is used in

conjunction with the word “WARNING” or “CAUTION.”

WARNING

Calls attention to actions or conditions that could cause

serious or fatal injury to the user, and precautions that can

be taken to prevent such occurrences.

CAUTION

Calls attentions to actions or conditions that could cause

light injury to the user or damage to the instrument or user’s

data, and precautions that can be taken to prevent such

occurrences.

Note

Calls attention to information that is important for proper

operation of the instrument.

Subheadings

On pages that describe the operating procedure in chapters 3 through 9 of Part 1 and

chapters 10 through 18 in Part 2, the following symbols are used to distinguish the

procedure from their explanations.

Procedure

Follow the numbered steps. All procedures are written with

inexperienced users in mind; experienced users may not

need to carry out all the steps.

Explanation

This section describes the setup items and the limitations

regarding the procedures. A detailed description of the

function is not provided in this section. For details on the

function, see chapter 2.

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 23 / 747

Результаты поиска

Содержание 701210

Отзывы: