YOKOGAWA 701210 Скачать руководство пользователя страница 198

Страница: 198 / 747

5-38

IM 701210-05E

5.18 Setting the Acceleration Measurement

<For a description of this function, refer to page 2-15.>

CAUTION

Before connecting the acceleration sensor, check that the bias current to the

sensor is OFF (see step 8 below). Otherwise, damage to the internal circuitry of

the acceleration sensors may result.

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press one of the keys from

CH1

CH16

to select the desired channel (select a

channel with the 701275(ACCL/VOLT) installed).

Press the

Coupling

soft key followed by the

ACCL

soft key.

Setting the Gain

Press the

Gain

soft key and select a value in the range of

0.1 to

100.

Setting the Sensitivity

Press the

Next 1/2

soft key.

Press the

Sensitivity

soft key.

Turn the

jog shuttle

and set the sensitivity of the acceleration sensor in the

range of 0.10 mV/Unit to 2000.00 mV/Unit.

Setting the Unit

The default value is m/s

. Change the unit as necessary.

Press the

Unit

soft key to display a software keyboard, and enter the unit

according to the procedure given in section 4.2.

Connecting the Acceleration Sensor

8. Press the

Bias

soft key to select OFF.

9. Connect the acceleration sensor according to the procedures given in section 3.12.

Setting the Bias Current Supply

10.

Press the

Bias

soft key to select ON.

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 198 / 747

Результаты поиска

Содержание 701210

Отзывы: