YOKOGAWA 701210 Скачать руководство пользователя страница 17

Страница: 17 / 747

Part 1:vi

IM 701210-05E

Standard Accessories

The standard accessories below are supplied with the instrument. Check that all

contents are present and undamaged.

Cover panels
B8023EN 8 pieces

• User’s Manual Part 1
• User’s Manual Part 2
• Operation Guide

AAA Alkaline batteries

(for acquisition memory
backup)

A1070EB 4 cells

Front panel protection
cover (transparent)
B8023EA

Soft case
B9946EB

• Communication Interface User’s
Manual (CD-ROM) B8023YZ
• Handling of the CD-ROM

Rubber feet
B9989EX 4 pieces (1 sheet)

DC power connector
(for the /DC model)
B8023WZ

Printer roll paper

For the DL750*
B9988AE
3 rolls

For the DL750P*
701966
1 roll

* Either one is included

depending on the model

Roll paper flange
(DL750P only)
B8024CA 2 pieces

UL/CSA Standard
A1006WD

VDE Standard
A1009WD

BS Standard
A1054WD

AS Standard
A1024WD

Power Cord (one of the following power cords
is supplied according to the instrument’s suffix codes)

GB Standard
A1064WD

Input Modules (Sold Separately)

Check that the MODEL indicated on the input module is what you ordered.

MODEL

Name

Abbreviation

701250

High-Speed 10 MS/s, 12-Bit Isolation Module

HS10M12

701251

High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module

HS1M16

701255

High-Speed 10 MS/s, 12-Bit Non-Isolation Module

NONISO_10M12

701260

High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS)

HV (with RMS)

701261

Universal (Voltage/Temp.) Module

UNIVERSAL

701262

Universal (Voltage/Temp.) Module (with AAF)

UNIVERSAL (AAF)

701265

Temperature, High Precision Voltage Isolation Module

TEMP/HPV

701270

Strain Module (NDIS)

STRAIN_NDIS

701271

Strain Module (DSUB, Shunt-Cal)

STRAIN_DSUB

701275

Acceleration/Voltage Module (with AAF)

ACCL/VOLT

701280

Frequency Module

FREQ

MODEL

NO.

SUFFIX

Made in Japan

MODEL

NO.

SUFFIX

Made in Japan

701250

HS10M12

Top row:

MODEL

Bottom row: Abbreviated name

This user’s manual refers to the input modules by MODEL (abbreviation).

For example, the High-Speed 10 MS/s, 12-Bit Isolation Module is indicated as 701250

(HS10M12). However, the module may be indicated only by the model (701250) if a

description about the same module is given immediately before it.

Checking the Contents of the Package

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 17 / 747

Результаты поиска

Содержание 701210

Отзывы: