YOKOGAWA 701210 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 162

5-2

IM 701210-05E

5.2

Setting T/div

<For a description of this function, refer to page 2-3.>

Procedure

MEASURE CURSOR

RESET

SELECT

CH

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

1

CH

2

CH

3

CH

4

CH

5

CH

6

CH

7

CH

8

CH

9

CH

10

CH

11

CH

12

CH

13

CH

14

CH

15

CH

16

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

7

DSP 1

8

9

DSP 2

6

5

4

1

0

2

3

ENTER

m

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

1.

Turn the TIME/DIV knob to set the T/div value.

Note

•

If the TIME/DIV knob is turned while the waveform acquisition is stopped, the new T/div
value is displayed within the parentheses at the upper right corner of the screen. The new
T/div value becomes valid the next time acquisition is started.

•

For details on the relationship between T/div and the sample rate, see appendix 1,
“Relationship between the Time Axis Setting, Sample Rate and Record Length.”

•

For a description of the T/div setting of the sub waveform of the dual capture function, see
section 7.6.

Explanation

Set the time per division on the screen grid.

Selectable T/div Range

500 ns/div to 3 day/div

Maximum Sample Rate

The maximum sample rate varies depending on the input module as follows.

Input Module

Maximum Sample Rate

701250 (HS10M12)

10 MS/s (5 MS/s)

701251 (HS1M16)

1MS/s

701255 (NONISO_10M12)

10 MS/s (5 MS/s)

701260 (HV (with RMS))

100 kS/s

701261 (UNIVERSAL)

100 kS/s (when measuring voltage), 500 Hz (data update
rate when measuring temperature)

701262 (UNIVERSAL (AAF))

100 kS/s (when measuring voltage), 500 Hz (data update
rate when measuring temperature)

701265 (TEMP/HPV)

500 Hz (data update rate)

701270 (STRAIN_NDIS)

100 kS/s

701271 (STRAIN_DSUB)

100 kS/s

701275 (ACCL/VOLT)

100 kS/s

701280 (FREQ)

25 kHz (data update rate)

Values inside the parentheses are those when the DSP channel (optional) is ON.

Note

The maximum sample rate of a DSP channel (optional) is 100 kS/s.

T/div and Roll Mode

The display switches to roll mode if T/div is set to 100 ms/div to 3 day/div under the

following conditions.

• Acquisition mode is set to a mode other than averaging.

• The trigger mode is set to auto, auto level, single, or log.

• The time base is set to the internal clock signal.

«
...
160
161
162
163
164
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов