YOKOGAWA 701210 Скачать руководство пользователя страница 159

Страница: 159 / 747

4-21

IM 701210-05E

Common Operations

4.6

Performing Calibration

Calibrate the DL750/DL750P when observing voltages.

Procedure

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Executing Calibration

Press

SHIFT+SETUP

Press the

Calibration

soft key to execute calibration.

Perform Auto Calibration

Press the

AutoCal

soft key to select ON.

Explanation

Calibration

The following parameters are calibrated. Perform calibration when you wish to measure

waveforms with high accuracy.

• Ground level offset

• A/D converter gain

Precautions to Be Taken When Perform Calibration

• Always allow the instrument to warm up for at least 30 minutes after the power is

turned ON before starting calibration. If calibration is performed immediately after the

power is turned ON, the calibration may be inaccurate due to drift caused by

fluctuation in the temperature of the instrument.

• Calibration must be performed when the temperature of the instrument is stable and is

between 5

C and 40

C (preferably at 23

C).

Note

The calibration described above is performed automatically when power is turned ON or
when the Cal Exec soft key in the Calibration menu is pressed.

Auto Calibration

If AutoCal is set to ON, auto calibration is performed the first time the time axis setting

(T/div) is changed or the first time measurement is started after the time shown below

passes.

After turning ON the power

• 3 minutes pass

• 10 minutes pass

• every 30 minutes from here on after

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 159 / 747

Результаты поиска

Содержание 701210

Отзывы: