YOKOGAWA 701210 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 747

YOKOGAWA 701210 Скачать руководство пользователя страница 138

3-35

IM 701210-05E

Making Preparations for Measurements

3

Specifications of the Optional Speaker Cable (701952) (Sold Separately) and
Connection Procedure

Use the speaker cable (701952) only to connect the DL750/DL750P to a speaker. For

details on the connection of the speaker cable and the speaker, follow the instructions

that came with the speaker.

1

6

Approx. 1.5 m

RJ-12 connector

To the DL750/DL750P

Wires are separated.
Modify them to suit your needs.

Pin No.

Signal Name

5
6

GND
SPEAKER

Wire Color
Blue
White

CAUTION

Do not short the speaker output signal or apply an external signal. Such act can

lead to malfunction or fire.

Note

•

For a speaker, use a commercially sold speaker with an impedance of 8

Ω

.

•

Depending on the speaker, a large sound may be produced even if the speaker volume of
the earphone microphone is set properly. When using a speaker for the first time, set the
speaker volume to the smallest setting. Some sound will be produced even if the volume
is set to the minimum setting. If the sound is still large even with the smallest volume
setting, turn the REC LEVEL knob on the left side panel at the time of recording to lower
the recording level.

Speaker Output Terminal (GO/NO-GO) Specifications

The terminal is shared with the GO/NO-GO I/O terminal of the DL750/DL750P side

panel.

Type

Modular jack (RJ-12). For the cable, use the optional speaker cable (701952) that is

sold separately.

Pin Arrangement

6

1

1

Pin No.

Signal Name

2
3
4
5
6

NC (no connection)
START IN
GO OUT

GO/NO-GO

NOGO OUT

Connector on the
DL750/DL750P

GND
SPEAKER

Circuit Diagram

+

6

5

Speaker with an
impedance of 8

Ω

(Commercially sold
product)

Speaker cable (701952)

(701952)

Amplifier

220

µ

F

3.14 Connecting the Earphone Microphone with a PUSH Switch and Connecting the Speaker

«
...
136
137
138
139
140
...
»

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов