YOKOGAWA 701210 Скачать руководство пользователя страница 118

Страница: 118 / 747

3-15

IM 701210-05E

Making Preparations for Measurements

3.6

Connecting Probes

Connect the probes (or other input cables such as BNC cables) to any of the input

terminals of the following modules. The input impedance is 1 M

Ω±

1% and

approximately 35 pF.

• High-Speed 10 MS/s, 12-Bit Isolation Module: 701250 (HS10M12)

• High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module: 701251 (HS1M16)

• High-Speed 10 MS/s, 12-Bit Non-Isolation Module: 701255 (NONISO_10M12)

• High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS): 701260 (HV (with RMS))

• Acceleration/Voltage Module (with AAF): 701275 (ACCL/VOLT)

• Frequency Module: 701280 (FREQ)

WARNING

• When connecting the item to be measured, be sure to turn OFF the power to the

item. Connecting or disconnecting the measuring lead while the item being

measured is turned ON is very dangerous.

• In Using the Modules

• Do not apply input voltage exceeding the maximum input voltage, withstand

voltage, or allowable surge voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth

grounding of the DL750/DL750P.

• To prevent the possibility of electric shock, be sure to fasten the module

screws. Otherwise, the electrical protection function and the mechanical

protection function will not be activated.

• Avoid continuous connection under an environment in which the allowable

surge voltage may occur.

• Use only specified cables. Using cables that do not meet the safety

specifications is extremely dangerous (especially when using high voltages

(42 V or higher).

• When using the 701250 (HS10M12) or the 701251 (HS1M16) to measure

high voltage, use the isolated probe (700929), 1:1 safety cable (combination

of 701901 and 701954), or the differential probe (700924).

• When applying high voltage using the 701260 (HV (with RMS)), 1:1 safety

cable (combination of 701901 and 701954) or the isolated probe (700929).

Содержание 701210












































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 701210

Отзывы:

YOKOGAWA 701210, Руководство пользователя, Страница: 118 / 747

Результаты поиска

Содержание 701210

Отзывы: