YMGI VRFI-07EW-D2B(55)5, Инструкция по установке и Руководство пользователя, Страница: 29 / 37

Note: Under the Dry Mode , the fan speed isn't adjustable, low fan speed is imperative.
"CLOCK" BUTTON: The time function runs on a 24-hour clock. To set the time press the CLOCK button once. You
will see a flashing clock appear on the remote. Press the "UP" button to increase the time; press the "DOWN" button
to decrease the time until the desired time is set. Press the CLOCK button once more to set the time. You will notice
the clock symbol is not flashing.
"LIGHT" BUTTON: This allows you to turn the indoor unit display light on and off. If the light emitted by the display
is not desired, simply press the LIGHT button on the remote and the display will turn off. To turn the display back on
simply press the light button once more.
"TURBO" BUTTON: When you press this button, you will see a symbol of a fan appear on the remote. In either
heat or cooling mode, when this button is pushed the compressor and or fan will blow at a higher speed to achieve
the set temp quicker. When the indoor unit senses that the set temp is being approached, the fan speed will slow
down. To turn this function off simply press the
TURBO button until the fan symbol is no longer displayed on the
remote.
"UP" Button: By pressing this button the set temperature will increase 1° each time the
“UP”
is pressed. If this
button is held for more than 2 seconds, the temperature will increase more rapidly. When operating in AUTO mode
the temperature cannot be changed. The temperature range for this remote is 61°F to 86°F. "DOWN" Button: By
pressing this button the set temperature will increase 1° each time the
“-”
is pressed. If this button is pushed without
releasing for over 2 seconds, the temperature will decrease more rapidly. In AUTO mode the temperature cannot be
changed. The temperature range for this remote is 61°F to 86°F.
"TEMP" Button: When the unit is first turned on the remote will display the last set temperature. When the TEMP
button is pushed twice the indoor unit will display the room temperature for approximately 5 seconds before going
back to the set temp.
SWITCH BETWEEN F ° AND C ° : The remote default is Fahrenheit. If you would like to switch between the remote
displaying Fahrenheit and Celsius the press the MODE and "DOWN" button simultaneously while the unit is turned
off.
"TIMER ON/OFF" BUTTON: This button allows you to set a time you would like the unit to turn on. The clock is a 24
hour clock. Press the TIMER ON/OFF button once and you will see the word "on" flashing next to a time displayed.
By pressing either the
“UP”
or
“DOWN“
button, choose the time you would like the unit to turn on. Once you have
the desired time displayed on the remote press the TIMER ON/OFF button once more and the word ON will stop
blinking and stay on the remote. The time you would like the unit to turn on is now set.
"TIMER ON/OFF" BUTTON: This allows you to set the time that you would like the unit to turn off. Simply follow the
above steps but this time press the TIMER ON/OFF button instead of the TIMER ON/OFF button. When the word
OFF is set on the remote screen, the time you would like the unit to turn off is now set.
"SWING" BUTTON: Hold the Swing Button (symbol shown above) for more than 2 seconds and the indoor air
louver will start to swing between the highest and lowest limits. Once the swing button is released the louver will stay
in the last position where the button was released. If the swing button is pushed just once the swing icon
will appear on the remote and the louver will swing up and down continuously between the highest and lowest points.
Push the
Swing Button once more and the icon will disappear on the remote and the louver will remain at the last
point the button was pushed. When the unit is powered off by the remote the louver will close on the indoor unit.
Press this button to set up the desired swing angle which circularly changes as below.
SWING UP AND DOWN” BUTTON
Press this button, to set up swing angle, which circularly changes as shown below: