Yeti SnowMX 2021, Руководство пользователя

Страница: 26 / 83

23 |
YETI SNOWMX USER MANUAL
CAUTION: Some of the repair or maintenance tasks
require the use of petroleum-based products, such
as oil or grease, that should not be handled directly
with unprotected hands. Use protective gloves that
are resistant to petroleum-based products. In case
of contact with skin, clean immediately with soap
and water.
MAINTENANCE - TASKS
• Inspect : Component(s) must be examined with
care. If an anomaly is noticed, the
malfunctioning component(s) must be repaired
or replaced.
• Clean : Component(s) must be cleaned of any
dirt, dust or contaminant liable to impair the
proper operation of the Conversion System.
• Adjust : Component(s) must be adjusted or re-
adjusted according to the manufacturer’s
adjustment recommendations. Refer to the
relevant section of the
User Manual
.
• Lubricate : Component(s) need to be lubricated
according to the manufacturer’s
recommendations. Refer to the relevant section
of the
User Manual
.
• Replace : Component(s) must be replaced to
avoid serious breakage.
MAINTENANCE - SPECIFICATIONS
System
• Visual Inspection : Visually inspect the
System’s components to detect any defect or
anomaly that can impair its proper functioning.
• Adjustment : Perform or verify angle of attack
adjustment on the suspension according to the
manufacturer’s recommendations. Refer to the
Adjustments
section on page 16.
• Bolt Torque : Check the torque of critical bolts
identified in the exploded views of the System.
Refer to the central pages of the
User Manual
.
CAUTION: Comply with tightening torque
recommendations and use a thread locker product
if you come across a bolt that is not tightened to the
manufacturer’s specifications.
• Chain - Adjustment: Perform or verify tension
adjustment on the System’s drive chain
according to the manufacturer’s
recommendations. Refer to the
Adjustments
section on page 19.
• Sprockets - Wear : Verify wear and general
condition of sprockets in chain drive mechanism.
Refer to “Wear” in the
Maintenance
section on
page 29. Replace sprockets if wear is too great.
• Chain - Wear : Verify wear and general condition
of chain in drive mechanism. Refer to “Wear” in
the
Maintenance
section on page 29. Replace
chain if wear is too great.
• Master link - Lubrication : Remove the chain’s
master link and grease the two pins according to
the maintenance chart recommendations. Refer
to “Lubrication” in the
Maintenance
section on
page 28.
• Chain - Lubrication : Lubricate the System’s
drive chain according to the maintenance chart.
Refer to “Lubrication” in the
Maintenance
section
on page 28.
CAUTION: If a chain needs to be replaced, its
sprockets should be replaced at the same time.
Assembly of new and used parts can speed up wear
of new components installed on the drive system.
• Brake Pads - Wear : Verify wear on brake pads.
Refer to “Wear” in the
Maintenance
section on
page 29. Replace brake pads if wear is too
great.
• Brake - Oil Level : With the vehicle upright and
on a level surface, check the oil level to make
sure that it is over the indicator mark on the
brake’s master cylinder sight glass. Add oil if
needed.
• Brake - Hydraulic pressure : Check brake lever
pressure. Bleed brake system if lever feels
spongy or ends its travel too close to the
handlebar. Refer to the
Brake Line Bleeding
section on page 15.
• Chain Tensioner - Wear : Verify wear and
general condition of Chain tensioner. Refer to
“Wear” in the
Maintenance
section on page 30.
• Syncro Drive Belt - Wear : Verify wear and
general condition of Syncro Drive Belt. Refer to
“Wear” in the
Maintenance
section on page 30.
• Drive Shaft Bearings : Check Drive Shaft
bearings for restriction, noise or abnormal play in
rotation. Bearings must absolutely be replaced if
they present a defect.