Yealink W80 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 260

background image

Account Settings

45

Fallback Server Redundancy Configuration

The following table lists the parameters you can use to configure fallback server redundancy.

Parameter

account.X.fallback.redundancy_type

[1]

<MAC>.cfg

Description

It configures the registration mode in fallback mode.

Note

: It is not applicable to outbound proxy servers.

Permitted
Values

0

-Concurrent registration

1

-Successive registration

Default

0

Parameter

account.X.fallback.timeout

[1]

<MAC>.cfg

Description

It configures the time interval (in seconds) for the phone to detect whether the working server is avail-
able by sending the registration request after the fallback server takes over call control.

Note

: It is not applicable to outbound proxy servers.

Permitted
Values

Integer from 10 to 2147483647

Default

120

[1]

X is the account ID. X=1-100.

Failover Server Redundancy Configuration

The following table lists the parameters you can use to configure failover server redundancy.

Parameter

account.X.sip_server.Y.register_on_enable

[1][2]

<MAC>.cfg

Description

It enables or disables the phone to send registration requests to the secondary server when encoun-
tering a failover.

Permitted
Values

0

-Disabled, the phone will not attempt to register to the secondary server, since the phone assumes

that the primary and secondary servers share registration information. So the phone will directly send
the requests to the secondary server.

1

-Enabled, the phone will register to the secondary server first, and then send the requests to it.

Default

0

Parameter

sip.skip_redundant_failover_addr

<y0000000000xx>.cfg

Description

It enables or disables the phone only to send requests to the servers with different IP addresses when
encountering a failover.

Permitted
Values

0

-Disabled

1

-Enabled

Default

1

Parameter

account.X.sip_server.Y.only_signal_with_registered

[1][2]

<MAC>.cfg

Description

It enables or disables the phone to only send requests to the registered server when encountering a
failover.

Note

: It works only if “account.X.sip_server.Y.register_on_enable” is set to 1 (Enabled) and “accoun-

t.X.sip_server.Y.failback_mode” is set to 1, 2 or 3.

Permitted
Values

0

-Disabled

1

-Enabled

Default

0

«
...
46
47
48
49
50
...
»

Содержание W80





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для W80

Бренд: Sangoma Страницы: 3

Бренд: XPLORA Страницы: 2

OfficeServ 7200

Бренд: Samsung Страницы: 137

Бренд: Samsung Страницы: 129

Бренд: Panasonic Страницы: 67

EXI5560 - EXI 5560 Cordless Extension...

Бренд: Uniden Страницы: 48

Бренд: Panasonic Страницы: 88

Бренд: Radio Shack Страницы: 36

Бренд: Centrios Страницы: 13

Бренд: Commax Страницы: 16

Бренд: Walker Ameriphone Страницы: 39

Бренд: Gentner Страницы: 31

Бренд: GE Страницы: 2

Бренд: AEG Страницы: 150

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды