Yealink W56P Telesystem Скачать руководство пользователя страница 83

Страница: 83 / 94

Troubleshooting



Ensure that the ringer volume of your handset is not adjusted to the minimum.
Refer to

Adjusting Volume

on page

2830



Ensure that the silent mode is not switched to On. Refer to

Switching Silent Mode

to On/Off

on page

3031

Why can I hear the verification tone from handset if the call is successfully handled by the
repeater?

To deactivate the verification tone on the repeater:

Switch off the repeater (disconnect the power adapter).

Switch it on for 1 to 5 seconds and switch it off again.

Switch it on again. The LED indicator on the repeater flashes slowly.

Switch it off again.

Switch it on again.

The verification tone is then deactivated. If you want to activate the verification
tone, repeat the above steps.

Display Issue

Why does the handset prompt the message “Not Subscribed”?

Check the registration status of your handset. If your handset is not registered to the base
station, register it manually. Refer to

Handset Registration

on page

Why does the handset prompt the message “Not in Range” or “Out Of Range”?



Ensure that the base station is properly plugged into a functional AC outlet.



Ensure that the handset is not too far from the base station.

Why does the handset prompt the message “Network unavailable.”?



Ensure that the Ethernet cable is plugged into the Internet port on the base station and the
Ethernet cable is not loose.



Ensure that the switch or hub in your network is operational.

Update & Reset Issue

How to upgrade firmware?

To upgrade base station/handset firmware via web user interface:

Click on Settings->Upgrade.

In the Select And Upgrade Firmware or Select and Upgrade Handset Firmware

Содержание W56P Telesystem































































































Результаты поиска

Содержание W56P Telesystem

Отзывы:

Похожие инструкции для W56P Telesystem

Бренды по названию

Популярные бренды

Yealink W56P Telesystem, Руководство пользователя

Результаты поиска

Содержание W56P Telesystem

Отзывы:

Похожие инструкции для W56P Telesystem

Бренды по названию

Популярные бренды