Yealink VC110 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 268

background image

Configuring Network

83

4) Click Upload to upload the certificate.

3.

Click Confirm to accept the change.

A dialog box pops up to prompt that the settings will take effect after a reboot.

4.

Click Confirm to reboot the endpoint immediately.

To configure the 802.1X via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->Advanced Network.

2.

Select the desired mode from the pull-down list of 802.1x Mode.

3.

Press the Save soft key to accept the change.

The display device prompts ―Reboot now?‖.

4.

Select OK to reboot the endpoint immediately.

The H.245 protocol is a control protocol that manages the media sessions. It is a part of
the H.323 protocol suite. The H.245 protocol is used primarily to negotiate the
master-slave relationship between communicating endpoints. The H.245 messages can
be encapsulated and carried between H.225 controlled endpoints within H.225
messages. This way of "piggy-backing" an H.245 message to the H.225 message is
referred to as H.323 Tunneling. The tunneling feature relies on H.225
endpoint-to-endpoint connectivity (via TCP) to pass H.245 messages, and uses the
H.225 communication channel without creating a separate TCP socket connection (per
H.323 call) for media control.

«
...
93
94
95
96
97
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: R.V.R. Elettronica Страницы: 38

CQDF783U - AUTO RADIO/CD DECK

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 145

Бренд: Panasonic Страницы: 66

Бренд: TANDBERG Страницы: 2

6000 MXP Profile

Бренд: TANDBERG Страницы: 2

3000 MXP Profile

Бренд: TANDBERG Страницы: 2

Бренд: TANDBERG Страницы: 11

Media Processing System MPS 800

Бренд: TANDBERG Страницы: 106

Бренд: TANDBERG Страницы: 44

Бренд: TANDBERG Страницы: 2

Бренд: TANDBERG Страницы: 11

Бренд: J&M Corporation Страницы: 9

DTM High Speed 7910

Бренд: Becker Страницы: 4

SCALA UTOPIA III EVO

Бренд: Focal Страницы: 52

Бренд: Yaesu Страницы: 39

Бренд: Imesa Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды