Yealink VC110 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 268

background image

Configuring Network

69

A dialog box pops up to prompt that the settings will take effect after a reboot.

5.

Click OK to reboot the phone.

To configure IPv6 address assignment method via phone user interface:

1.

Select Menu->Advanced (default password: 0000) ->LAN Configuration.

2.

Select IPv4 & IPv6 or IPv6 from the IP Mode field.

3.

Press or to highlight IPv6 and press .

4.

Select the desired IPv6 address assignment method.

If you uncheck the DHCP checkbox, configure the IPv6 address and other network
parameters in the corresponding fields.

5.

Press the Save soft key to accept the change.

The IP phone reboots automatically to make settings effective after a period of
time.

To configure static DNS when DHCP is used via phone user interface:

1.

Select Menu->Advanced (default password: 0000) ->LAN Configuration->IPv6.

2.

Check the DHCP checkbox.

3.

Check the Static DNS checkbox.

4.

Enter the desired values in the DNS Primary Server and DNS Secondary Server
fields respectively.

5.

Press the Save soft key to accept the change.

6.

The display device prompts ―Reboot now?‖.

7.

Select OK to reboot the endpoint immediately.

You can configure the network speed and duplex mode the endpoint uses. The network
speed and duplex mode you select for the endpoint must be supported by the switch.
The network speeds and duplex modes supported by the endpoint are:



Auto



10 Mbps Half Duplex



100 Mbps Half Duplex



10 Mbps Full Duplex



100 Mbps Full Duplex

Auto is configured on the endpoint by default.

Auto

Auto means that the switch will negotiate the network speed and duplex mode for the
endpoints to transmit voice or data over Ethernet. This process entails devices first

«
...
79
80
81
82
83
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Safeline Страницы: 8

Бренд: Fagor Страницы: 103

Бренд: Skytec Страницы: 12

Бренд: Roger Страницы: 2

Бренд: Vizio Страницы: 24

WEB’LOG RESIDENTIAL

Бренд: Meteo Control Страницы: 4

Бренд: VIS-A-VIS Страницы: 4

Бренд: Konftel Страницы: 8

Бренд: Bigben Страницы: 64

media:scape mini

Бренд: Steelcase Страницы: 7

Бренд: Favero Страницы: 27

VidyoConference

Бренд: Vidyo Страницы: 2

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 31

Бренд: Blaupunkt Страницы: 63

ARMT.665230.202-01

Бренд: ARMTEL Страницы: 36

Бренд: Brahler Страницы: 30

CMT-BX1 Marketing

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды