Yealink VC110 Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

224

4.

Click Confirm to confirm upgrading.

Note

We may need you to provide the endpoint configurations for the Yealink field
application engineers to help analyze problems. You can import configurations to your
endpoint to configure your endpoint quickly. The file format of configuration file must be
*.bin.

To export the endpoint configurations via web user interface:

1.

Click on Setting->Configuration.

2.

Click Export.

3.

Click Confirm to export the configurations.

To import the endpoint configurations via web user interface:

1.

Click on Setting->Configuration.

2.

Click Browse to locate a configuration file from your local endpoint.

3.

Click Import to import the configuration file.

Reset the endpoint to factory configurations after you have tried all appropriate
troubleshooting suggestions but still have not solved your problems.

Caution! Don‘t remove the Ethernet cable and power cord during the upgrade process.

Don‘t close or refresh the web page when upgrading the firmware via web user
interface.

«
...
234
235
236
237
238
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Handicare Страницы: 56

Бренд: Data I/O Страницы: 88

Бренд: Panasonic Страницы: 2

Бренд: MPS Страницы: 4

eyespeak zuvo 12-D

Бренд: Talk To Me Technologies Страницы: 28

Lumina LU20S-DNW

Бренд: Leviton Страницы: 3

Бренд: D-Link Страницы: 10

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 18

Бренд: Philips Страницы: 20

Allegiant LTC 8500 Series

Бренд: Philips Страницы: 91

Бренд: Steren Страницы: 3

Бренд: Riello Страницы: 12

Бренд: KSB Страницы: 40

Бренд: Fisher Страницы: 24

Бренд: Fisher Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды