Yealink VC110 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

152

6.

Select the desired value from the pull-down list of Date Format.

7.

Click Confirm to accept the change.

To configure the time and date format via the remote control:

1.

Select Menu->Basic->Date & Time.

2.

Configure the desired values.

3.

Press the Save soft key to accept the change.

The time and date displayed on the LCD screen of the display device and video
conferencing phone will change accordingly.

The endpoint will enter the sleep mode automatically when it has been inactive for a
period of time (the default time is 10 minutes). When the endpoint is in sleep mode, it
can still accept incoming calls. The display device will prompt ‖No Signal‖, and the LCD
screen of the video conferencing phone prompts ―Sleeping Press any key to resume‖.
You can press any key on the remote control or the video conferencing phone to wake
the endpoint up. When receiving a call, the endpoint will be woken up automatically.

You can change the automatic sleep time via the remote control or web user interface.
You can also press the sleep key on the remote control to make the endpoint sleep
immediately.

The automatic sleep time is described below:

Parameter

Description

Configuration Method

Automatic Sleep

Time

Configures the inactive time (in
minutes) before the endpoint
enter sleep mode.

Default: 10 Min

Note: During setup wizard, the
automatic sleep time feature is

Remote Control

Web User Interface

«
...
162
163
164
165
166
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Sena Страницы: 16

Бренд: Rath Страницы: 10

151 Musiccenter

Бренд: Burmester Страницы: 20

Бренд: Ubiquiti Страницы: 42

Бренд: AbleNet Страницы: 8

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 22

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 33

Бренд: Panasonic Страницы: 15

Termix VVX-I-R FI - 7 Series

Бренд: Danfoss Страницы: 32

Бренд: Lutron Electronics Страницы: 12

Бренд: Thermoline Scientific Страницы: 15

Бренд: Multilaser Страницы: 40

Бренд: Isel Страницы: 45

administration and

Бренд: AT&T Страницы: 404

Бренд: Crunch Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды