Yealink VC110 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

114

To configure SIP account via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->SIP Account.

2.

Configure the SIP account settings.

3.

Press the Save soft key to accept the change.

After successful registration, the display device displays , and the LCD
screen of the video conferencing phone displays .

When making an IP call using the SIP protocol, the endpoint doesn't support the TLS
protocol. So configuration parameters of SIP IP call are divided from the SIP account.
You can configure SIP IP call separately.

SIP IP call parameters on the endpoint are described below:

Parameter

Description

Configuration Method

SIP IP Call Enable

Enables or disables the SIP IP
Call.

Default: Enabled.

Note: When it is set to Enabled on
both sites, the VC110 can call the
far site by dialing an IP address
directly.

Remote Control

Web User Interface

Transport

Configures the type of transport
protocol for the SIP IP call.



UDP—provides best-effort
transport via UDP for SIP
signaling.



TCP—provides reliable
transport via TCP for SIP
signaling.



DNS-NAPTR—performs the
DNS NAPTR and SRV queries
for the service type and port
if no server port is given.

Remote Control

Web User Interface

To configure SIP IP call via web user interface:

1.

Click on Account->SIP IP Call.

2.

Select the desired value from the pull-down list of SIP IP Call Enable.

«
...
124
125
126
127
128
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Panasonic Страницы: 2

RXD15 - RADIO CASSETTE W/CD

Бренд: Panasonic Страницы: 8

ConferenceSHOT AV

Бренд: VADDIO Страницы: 114

Бренд: YASKAWA SIEMENS Страницы: 373

digital slim -1400

Бренд: Fisher Страницы: 20

Бренд: Skov Страницы: 68

Бренд: Verizon Страницы: 69

Бренд: ALLEN & HEATH Страницы: 14

SwitchPoint Infinity 3

Бренд: Stryker Страницы: 124

Бренд: Taiden Страницы: 91

Бренд: btsr Страницы: 73

Бренд: Creator Electronics Страницы: 52

Stealthbox SB-F-150-SCDBL/12TW3

Бренд: JL Audio Страницы: 5

Бренд: Mitsubishi Electric Страницы: 17

Бренд: Mitsubishi Electric Страницы: 20

Бренд: Mitsubishi Electric Страницы: 48

Бренд: Mitsubishi Electric Страницы: 20

MELDAS 600 Series

Бренд: Mitsubishi Electric Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды