Yealink VC110 Скачать руководство пользователя страница 111

Страница: 111 / 268

Configuring Network

Enter the keep alive interval in the Keep Alive Interval field.

Click Confirm to accept the change.

Rport in

RFC 3581

, allows a client to request that the server sends the response back to

the source port from which the request came. Rport feature depends on support from a
SIP server.

The rport parameter on the endpoint is described below:

Parameter

Description

Configuration Method

RPort

Enables or disables NAT Rport
feature. You can configure it for
the SIP account or SIP IP call
separately.

Default: Enabled

Web User Interface

To configure rport feature for SIP account via web user interface:

Click on Account->SIP Account.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды