Yealink MeetingSpace VC200 страница 225 Скачать руководство пользователя

Страница: 225 / 232

| Troubleshooting |

225

Situation

Reason

Solution

Your monitor prompts: Call Fail

Busy Here.
• Far site rejects your SIP call.
• Far site does not answer your

SIP call.

• Far site has reached maximum

sessions when you place a SIP

call.

Contact the far site.

Your monitor prompts: Call Fail

Remote endpoint refused call.
Far site rejects your H.323 call
• Far site rejects your H.323 call.
• Far site does not answer your

H.323 call.

• Far site has reached maximum

sessions when you place an

H.323 call.

Contact the far site.

Your monitor prompts: Network

disconnected

Check the network connection.

Your monitor prompts: Maximum

number of sessions reached.

The maximum sessions is depend

on the multipoint license imported

to the system.

Audio Issues

Symptom

Reason

Solution

The volume is set to 0.

Adjust the volume.

You cannot hear the audio during a

call.

The far site mutes the microphone. Contact the far site to check

whether the microphone is

unmuted.

The speaker volume is too low.

Adjust the volume.

The muffled audio reception from

the far site may be caused by

highly reverberant rooms.

Contact the far site to speak in

close proximity to the phone.

You choose a low-bandwidth audio

codec.

Adjust the priority order of your

audio codec.

You cannot hear the audio clearly

during a call.

Noise devices, such as computers

or fans.

Enable noise suppression.

Содержание MeetingSpace VC200









































































































































































































































Результаты поиска

Содержание MeetingSpace VC200

Отзывы:

Похожие инструкции для MeetingSpace VC200

Бренды по названию

Популярные бренды

Yealink MeetingSpace VC200, Руководство администратора

Результаты поиска

Содержание MeetingSpace VC200

Отзывы:

Похожие инструкции для MeetingSpace VC200

Бренды по названию

Популярные бренды